ADTRAN ATLAS 550 Скачать руководство пользователя страница 178 | Manualshive

Страница: 178 / 412

background image

Section 4 User Interface Guide

ATLAS 550 System Manual

178

© 2004 ADTRAN, Inc.

61200305L2-1B

M

ODULES

(VCOM-

X

) > S

TATISTICS

Write security: 4; Read security: 5

These options initiate different types of tests and display test results.

M

ODULES

(VCOM-

X

) > S

TATISTICS

> D

EVICE

Read security: 5

Indicates the resource number of the packet voice device listed. On the ATLAS 550, packet voice devices
are numbered 1-24.

M

ODULES

(VCOM-

X

) > S

TATISTICS

> U

SAGE

T

IME

Read security: 5

Measures the total elapsed time that a packet voice device has the status

B

USY

. The time is expressed with

millisecond precision. Available packet voice devices are assigned new connections using a round-robin
technique where all other available packet voice devices must be used before a given device is assigned a
new connection. This scheme tends to use all packet voice devices evenly. If a given device shows
significantly less elapsed usage time than other packet voice devices on the same ATLAS 550, that device
may be faulty.

M

ODULES

(VCOM-

X

) > S

TATISTICS

> ATLAS F

RMS

Read security: 5

(ATLAS Frames) Counts every frame that the ATLAS 550 sends to or receives from the packet voice
device. This count indicates activity but does not indicate the actual amount of frame relay data exchanged.
The total number of frames handled by the packet voice device is given by the following equation:

See the

ATLAS D

ROP

definition below for a description of the term:

M

ODULES

(VCOM-

X

) > S

TATISTICS

> ATLAS D

ROP

Read security: 5

A counter that measures each frame that is dropped or discarded during communication between the
ATLAS 550 and the packet voice device; i.e., ATLAS Frames Dropped. The exchange protocol is designed
so that no frames should be discarded during this operation. A consistent pattern of dropped frames by a
given packet voice device may indicate a faulty packet voice device or an overloaded ATLAS 550 system.

The discarded frame indicated by this value does not reflect network-level performance
management but indicates an anomalous condition within the ATLAS 550 unit.
Persistently dropped frames may indicate a problem with the ATLAS 550 unit or the Voice
Compression Resource Module.

Frames

ATLAS

(

)

Total

Frames

ATLAS

Frames

ATLAS

(

)

Dropped

+

=

Frames

ATLAS

(

)

Dropped

«
...
176
177
178
179
180
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

ControlMaster CM15

Бренд: ABB Страницы: 28

Бренд: YASKAWA Страницы: 256

Бренд: HANYOUNG NUX Страницы: 36

Бренд: HANYOUNG NUX Страницы: 4

Бренд: MADRIX Страницы: 91

Бренд: MADRIX Страницы: 40

Бренд: YASKAWA Страницы: 18

Бренд: Objective Imaging Страницы: 11

Бренд: R-Tec Страницы: 14

Бренд: Nations Страницы: 654

GVB-8-WP Series

Бренд: Genasun Страницы: 8

Бренд: Rain Bird Страницы: 20

DECORA ILLUMATECH IPF01-1LX

Бренд: Leviton Страницы: 2

All Sport 1600 Series

Бренд: Daktronics Страницы: 92

Бренд: Kramer Страницы: 16

Бренд: Trinamic Страницы: 17

Бренд: H3C Страницы: 3

DMX LED EASY Operator Deluxe

Бренд: EuroLite Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды