ADTRAN ATLAS 550 Скачать руководство пользователя страница 190

Страница: 190 / 412

Section 4 User Interface Guide

ATLAS 550 System Manual

190

61200305L2-1B

ACKET

ANAGER

> P

ACKET

NDPNTS

> P

ERFORMANCE

Write security: 3; Read security: 5

Displays performance information for each packet endpoint including the endpoint name, the protocol
used, link stats, and sublink stats.

ACKET

ANAGER

> P

ACKET

NDPNTS

> P

ERFORMANCE

> E

NDPNT

AME

Read security: 5

Displays the packet endpoint name as defined in the

ACKET

NDPNTS

ONFIG

menu (see also

Packet

Manager > Packet Endpnts > Config > Endpnt Name

on page 193).

ACKET

ANAGER

> P

ACKET

NDPNTS

> P

ERFORMANCE

> P

ROT

Read security: 5

Displays the layer 2 protocol for this packet endpoint.

indicates this packet endpoint is configured for

frame relay.

TBOP

indicates this packet endpoint is configured for Transparent Bit Oriented Protocol

(TBOP).

PPP

indicates this packet endpoint is configured for the Point-to-Point Protocol.

SDLC

indicates

this packet endpoint is configured for SDLC signaling.

ACKET

ANAGER

> P

ACKET

NDPNTS

> P

ERFORMANCE

> L

INK

TATS

- F

RAME

ELAY

Write security: 3; Read security: 5

Displays layer 2 performance statistics. The statistics fields for frame relay reflect the total count since last
cleared. The available statistic information is discussed below.

SDLC signaling is only available using the Legacy Data Option Module (P/N 1200342L1).

ACKETS

Total number of frame relay packets transmitted through this packet
endpoint, including both user data (on all PVCs) and signaling.

ACKETS

Total number of frame relay packets received through this packet endpoint
on all PVCs.

TATE

HANGES

Total number of times that frame relay signaling has gone active or
inactive.

IGNALING

RRORS

Total number of signaling frames received with PVC signaling protocol
violations.

IGNALING

IMEOUTS

Number of times signaling polls were not received in the time specified in

T391

in the

ACKET

NDPTS

ONFIG

menu.

SYNC

TATUS

Full status not transmitted during the normal full status cycle. An
asynchronous status message is used to quickly activate a link.

SYNC

TATUS

Full status not received during the normal full status cycle. An
asynchronous status message is used to quickly activate a link.

ULL

TATUS

Number of full status polls transmitted by this packet endpoint.

ULL

TATUS

Number of full status polls received by this packet endpoint.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды