ADTRAN ATLAS 550 Скачать руководство пользователя страница 175 | Manualshive

Страница: 175 / 412

background image

ATLAS 550 System Manual

Section 4 User Interface Guide

61200305L2-1B

© 2004 ADTRAN, Inc.

175

M

ODULES

(VCOM-

X

) > S

TATUS

> S

TATUS

Read security: 5

Indicates the condition of the individual packet voice device. This field may display the following:

M

ODULES

(VCOM-

X

) > S

TATUS

> A

LGORITHM

Read security: 5

Denotes the voice compression algorithm being used by the packet voice device. Any packet voice device
can use any available compression algorithm. When ATLAS 550 chooses a packet voice device for a
particular call, the voice compression algorithm is set to match the dial plan endpoint configuration. Refer
to the Frame Relay menu section of this manual for more information.

M

ODULES

(VCOM-

X

) > S

TATUS

> S

ILENCE

Read security: 5

Voice endpoints continue to originate frame relay traffic during periods of relative silence. The

ATLAS 550 expects to receive such silence frames; therefore, silence compression is

D

ISABLED

by default.

Some voice endpoints can be configured so that no silence frames are transmitted during periods of relative
silence. For compatibility with these devices, the ATLAS 550 can be configured to expect that silence
suppression is

E

NABLED

; thus, no frame relay traffic is generated during periods of silence. Both voice

endpoints must agree on the silence suppression setting.

N/A

This device is not populated on the selected VCOM Resource Module.

A

VAILABLE

This resource is available for voice compression and functioning properly. If a
VCOM-4 Option Module is installed, 4 voice compression resources will be

A

VAILABLE

and the rest will display

N/A

. The same principle applies to the

VCOM-8, 24, and 32 Option Modules.

P

ENDING

This resource is currently changing state.

B

USY

This resource is currently in use.

T

ESTING

This resource is currently being tested and is not available for use.

F

AILED

This resource has failed testing and is not available for use.

R

ELOADED

This resource was reinitialized after excessive errors.

N/A

This device has not been assigned a voice compression algorithm.

G.723.1

CCITT G.723.1 compression; 6.3 kbps bandwidth.

N

ETCODER

Proprietary NETCODER compression; 6.4 kbps bandwidth.

Some voice compression standards may be used only under specific licensing
arrangements due to existing patents. The ATLAS 550 provides complete management of
these licensed resources; therefore, users are not required to take additional steps to
ensure conformance with licensing provisions. For example, the ATLAS 550 manages its
resources so users never exceed the maximum licensed number of simultaneous
connections.

«
...
173
174
175
176
177
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

Бренд: Oldham Страницы: 32

Бренд: Wesa Страницы: 8

Бренд: Mitsubishi Страницы: 30

Бренд: Joy-it Страницы: 7

Бренд: Riello Страницы: 72

Бренд: Carrier Страницы: 4

CIMR-VC*****H**-00 series

Бренд: YASKAWA Страницы: 32

ARES-1231 Series

Бренд: Arbor Technology Страницы: 94

SATLOC GPSteer LiteStar II

Бренд: CSI Wireless Страницы: 7

MICROMEGA CN77000 series

Бренд: Omega Страницы: 104

Бренд: Haiwell Страницы: 23

Бренд: Grundfos Страницы: 32

Бренд: Yatai Страницы: 7

Бренд: Fuji Electric Страницы: 20

Бренд: Lemona Страницы: 3

Бренд: Acclaim Lighting Страницы: 41

Бренд: Oasis Aquatics Страницы: 4

Бренд: PI Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды