ADTRAN ATLAS 550 Скачать руководство пользователя страница 134

Страница: 134 / 412

Section 4 User Interface Guide

ATLAS 550 System Manual

134

61200305L2-1B

ODULES

(V35N

-2) > T

EST

Write security: 4; Read security: 5

These options initiate different types of tests and display test results.

ODULES

(V35N

-2) > T

EST

> P

ORT

Indicates operating port. There are 2 available interfaces on the Dual Nx56/64 Option Module.

ODULES

(V35N

-2) > T

EST

> L

OOPBACK

Write security: 4; Read security: 5

Test pattern to be transmitted out the port. The following options are available:

ODULES

(V35N

-2) > T

EST

> L

OOPBACK

TATUS

Read security: 5

This read-only option indicates a port’s current loopback status by displaying any of the following status
messages:

ODULES

(V35N

-2) > T

EST

> 511

Write security: 4; Read security: 5

Controls the activation of the 511 test pattern generator and detector.

ODULES

(V35N

-2) > T

EST

> 511 R

ESULT

Read security: 5

Displays the results of the 511 test. This option is read-only. Clear these results by pressing <Enter> when

CLR

is selected.

OOPBACK

No active loopback.

OCAL

OOPBACK

Activates both a local loopback (back toward the DTE) and a port
loopback (toward the network).

EMOTE

OOPBACK

V.54 loopback code to be sent to the far end, and if the device at the far
end supports V.54, the device activates a loopback on detection of the
V.54 code.

OOPBACK

CTIVE

EMOTE

OOP

-U

AILED

OOPING

EMOTE

NIT

ORT

OOPED

ROM

EMOTE

OURCE

EMOTE

NIT

OOPED

ACK

ORT

OOPBACK

CTIVE

OOPING

OWN

EMOTE

NIT

ONE

Pattern is not synchronized.

LOS

At one point the pattern was synchronized, but is currently not
synchronized.

YNC

Pattern is synchronized.

Number of seconds with at least one bit error.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды