ADTRAN ATLAS 550 Скачать руководство пользователя страница 193

Страница: 193 / 412

ATLAS 550 System Manual

Section 4 User Interface Guide

61200305L2-1B

193

ACKET

ANAGER

> P

ACKET

NDPNTS

> C

ONFIG

Write security: 3; Read security: 5

Creates and configures packet endpoints.

ACKET

ANAGER

> P

ACKET

NDPNTS

> C

ONFIG

> E

NDPNT

AME

Write security: 3; Read security: 5

Alphanumeric string (up to 16 characters in length) to enter a user-definable name (such as the name of the
frame relay provider or the circuit ID).

TATISTICS

Write security: 3; Read security: 5

Provides additional information, as follows, on the individual sublink:

ESET

OUNTERS

Write security: 3; Read security: 5

Resets all sublink counters.

FECN C

OUNT

Write security: 3; Read security: 5

Total number of FECN bits received on this PVC.

BECN C

OUNT

Write security: 3; Read security: 5

Total number of BECN bits received on this PVC.

DE D

ISCARD

OUNT

Write security: 3; Read security: 5

Total number of Discard Eligible bits that have been received on this PVC.

CTIVE

LAGS

Write security: ADTRAN USE ONLY

For ADTRAN internal use only.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды