ADTRAN ATLAS 550 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 412

background image

ATLAS 550 System Manual

Section 4 User Interface Guide

61200305L2-1B

© 2004 ADTRAN, Inc.

81

S

YSTEM

C

ONFIG

> S

ESSION

T

IMEOUT

Write security: 3; Read security: 5

Defines the number of seconds the terminal session must remain idle before the session times out (valid
range 0 to 65535). You can enter zero to deactivate this option (the session will never time out).

S

YSTEM

C

ONFIG

> M

AX

T

ELNET

S

ESSIONS

Write security: 3; Read security: 5

Defines the maximum number of Telnet sessions that can be active at the same time. Enter a number
between 0 and 12 in this field.

S

YSTEM

C

ONFIG

> E

THERNET

P

ORT

Write security: 2; Read security: 5

Provides a way to configure various settings for the

ETHERNET

port. The following options are available

for review and editing:

S

YSTEM

C

ONFIG

> E

THERNET

P

ORT

> P

ORT

N

AME

Write security: 2; Read security: 5

Defines the name of the

ETHERNET

port. Enter up to 16 alphanumeric characters in this field, including

spaces and special characters (such as underbar). This field may be left blank.

S

YSTEM

C

ONFIG

> E

THERNET

P

ORT

> IP A

DDRESS

Write security: 2; Read security: 5

Lists the address assigned to the base

ETHERNET

port. This address is in dotted decimal notation (four

decimal numbers, each in the range of 0 to 255, separated by periods). This value is set to 10.0.0.1 by
default. The IP address is used for the 10/100BaseT

ETHERNET

interface. Obtain the correct IP address

from your LAN administrator.

S

YSTEM

C

ONFIG

> E

THERNET

P

ORT

> D

EFAULT

G

ATEWAY

Write security: 2; Read security: 5

Defines or changes the default gateway. Enter the default gateway address by entering a decimal number
into the appropriate field and then pressing <Enter> to move to the next field. You will need a default
gateway if the LAN contains multiple segments. This address is in dotted decimal notation (four decimal
numbers, each in the range of 0 to 255, separated by periods). This value is set to 0.0.0.0 by default.
Contact your LAN administrator for the appropriate address.

S

YSTEM

C

ONFIG

> E

THERNET

P

ORT

> S

UBNET

M

ASK

Write security: 2; Read security: 5

Defines which part of a destination IP address contains the network number. This address is in dotted
decimal notation (four decimal numbers, each in the range of 0 to 255, separated by periods). This value is
set to 255.255.255.0 by default. This part of the destination IP address is used along with the ATLAS 550
IP address to determine which nodes must be reached through the default IP gateway.

If you enter zero in this field, you will not be able to use Telnet. Only enter zero if you want
to completely lock out Telnet access.

«
...
79
80
81
82
83
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

Бренд: Daikin Страницы: 48

Бренд: Daikin Страницы: 77

Бренд: Daikin Страницы: 32

Бренд: Daikin Страницы: 14

Бренд: Daikin Страницы: 16

Бренд: Daikin Страницы: 1

Бренд: Lattice Страницы: 23

Бренд: IBC Страницы: 8

Бренд: Gardena Страницы: 236

Бренд: Maximum Controls Страницы: 58

Бренд: HEIDENHAIN Страницы: 257

VLTAutomationDrive FC 360

Бренд: Danfoss Страницы: 52

Бренд: AirCycler Страницы: 2

Torque Converter Lock-Up

Бренд: TS Performance Страницы: 4

Бренд: Kohzu Precision Страницы: 58

Бренд: Shimaden Страницы: 16

KaDe KDH-KZ620U

Бренд: AAT Holding Страницы: 28

Бренд: KELCO Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды