ADTRAN ATLAS 550 Скачать руководство пользователя страница 32

Страница: 32 / 412

Section 2 Engineering Guidelines

ATLAS 550 System Manual

61200305L2-1B

ADMIN Port (USOC RJ-48C)

The

ADMIN

port (EIA-232) connects to a computer or modem (see Table 4 for the pinout) and provides the

following functions:

•

Accepts EIA-232 input from a PC or a modem for controlling the ATLAS 550.

•

Operates at 2400, 9600, 19200, or 38400 bps.

•

Acts as input for either VT100 or PC control.

•

Acts as an interface for flash memory software downloads using XMODEM.

Ethernet Connection (USOC RJ-48C)

The

ETHERNET

port (RJ-48C) provides a 10/100BaseT

ETHERNET

LAN connection, which is used for

IP routing

TFTP, SNMP, and Telnet connections. Table 5 shows the pinout.

Table 4. ADMIN Port Pinout

Pin

Name

Description

Signal Ground

RTS

Request to Send (output), follows CTS

Transmit Data (input)

DTR

Data Terminal Ready (output), +12 V

Receive Data (output)

DCD

Data Carrier Detect (input)

—–

Not Connected

CTS

Clear to Send (input)

Table 5. Ethernet Pinout

Pin

Name

Description

TX1

Transmit Positive

TX2

Transmit Negative

RX1

Receive Positive

4, 5

—–

Unused

RX2

Receive Negative

7, 8

—–

Unused

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды