ADTRAN ATLAS 550 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 412

background image

ATLAS 550 System Manual

Compliance Information

61200305L2-1B

© 2004 ADTRAN, Inc.

5

Compliance Information

FCC regulations require that the following information be provided to the customer:

1. This equipment complies with Part 68 of the FCC rules and requirements adopted by ACTA. On

the equipment housing is a label showing the FCC registration number and ringer equivalence
number (REN). If requested, provide this information to the telephone company.

2. If this equipment causes harm to the telephone network, the telephone company may temporarily

discontinue your service. If possible, advance notification is given; otherwise, notification is given
as soon as possible. The telephone company will advise the customer of the right to file a
complaint with the FCC.

3. The telephone company may make changes in its facilities, equipment, operations, or procedures

that could affect the proper operation of this equipment. Advance notification and the opportunity
to maintain uninterrupted service are given.

4. If experiencing trouble with this equipment, please contact ADTRAN for repair and warranty

information. The telephone company may require this equipment to be disconnected from the
network until the problem is been corrected or it is certain the equipment is not malfunctioning.

5. This unit contains no user-serviceable parts.
6. An FCC compliant telephone cord with a modular plug is provided with this equipment. This

equipment is designed to be connected to the telephone network or premises wiring using an FCC
compatible modular jack, which is complaint with Part 68 and requirements adopted by ACTA.

7. The following information may be required when applying to your local telephone company for

leased line facilities.

8. The REN is used to determine the quantity of devices which may be connected to the telephone

line and still have all of those devices ring when the number is called. Excessive RENs on the
telephone line may result in the devices not ringing in response to an incoming call. In most, but
not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices
that may be connected to a line, as determined by the total RENs, contact the local telephone
company.

9. This equipment may not be used on coin service provided by the telephone company. Connection

to party lines is subject to state tariffs. Contact your state public utility commission or corporation
commission for information.

Part #

FCC Reg. Number

Service Type

REN/SOC

FIC

USOC

1200307L1

HDCUSA-34602-DE-N

1.544 Mbps - SF

1.544 Mbps - SF and B8ZS

1.544 Mbps - ESF

1.544 Mbps - ESF and B8ZS

6.0 N

04DU9-BN

RJ-48C

1200307L2

US:HDCDENAN1200307L2

04DU9-BN

1200314L1

HDCUSA-34601-DE-N

04DU9-BN

1200314L2

US:HDCDENAN1200314L2

04DU9-DN

1200346L1

US:HDCDENAN1200346L1

04DU9-1KN

1200346L2

US:HDCDENAN1200346L2

04DU9-1KN

1200755L1

HDCUSA-34601-DE-N

04DU9-1SN

1200755L2

US:HDCDENAN1200755L2

04DU9-1SN

1200310L1

HDCUSA-34761-KX-N

Analog Loop Start

0.1B/9.0F

02LS2

RJ-11C

1200329L1

HDCUSA-34761-KX-N

Analog Loop Start

0.1B/9.0F

02LS2

RJ-11C

1200341L1

HDCUSA-44569-MD-E

Analog Loop Start

0.8 B

N/A

RJ-11C

1200315L1

HDCUSA-34956-DE-N

Basic Rate ISDN

6.0 N

02IS5

RJ-49C

1200327L1

US:HDCDENAN1200327L1

Basic Rate ISDN

6.0 N

02IS5

RJ-49C

1200764L1

US:HDCXDNAN1200764L1

Basic Rate ISDN

6.0 N

02IS5

RJ-49C

«
...
3
4
5
6
7
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

Бренд: ZKTeco Страницы: 14

Бренд: Unico Страницы: 164

Бренд: Dantherm Страницы: 20

Бренд: Click2Enter Страницы: 34

Бренд: Auber Страницы: 3

Бренд: phytron Страницы: 55

Бренд: SKF Страницы: 11

Бренд: Danfoss Страницы: 162

SmarTemp Control fx

Бренд: Webasto Страницы: 8

8745 MFC Ethernet

Бренд: Burkert Страницы: 70

Бренд: adept technology Страницы: 96

Бренд: Walchem Страницы: 43

Бренд: YASKAWA Страницы: 38

Бренд: DAGON Страницы: 8

Бренд: D+H Страницы: 16

Бренд: National Instruments Страницы: 18

Бренд: TrailMaster Страницы: 2

Бренд: DeZurik Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды