ADTRAN ATLAS 550 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 412

background image

ATLAS 550 System Manual

Section 2 Engineering Guidelines

61200305L2-1B

© 2004 ADTRAN, Inc.

29

Table 3. Description of ATLAS 550 LEDs

For these LEDs...

This color light...

Indicates that...

System Status

Power

Green

the unit is on.

Off

the unit is off.

System

Green (solid)

no diagnosed system faults were found.

Green (fast blink)

a flash download is in progress.

Yellow (solid)

a fault was diagnosed, but the condition no longer exists.
The condition will be recorded in the system log.

Red (solid)

an error condition with either the power supply or the
system temperature is present.

Red (fast blink)

a fatal error occurred during flash download.

Off

power is not currently supplied to the system.

Ethernet

Green (solid)

the physical link is up.

Green (flashing)

there is activity on the LAN.

Off

the physical link is down - no Ethernet connection.

Remote

Yellow

a user is logged into the system via the

ADMIN

/

CRAFT

port or via the

ETHERNET

port.

Off

there are no users logged into the system.

Network Modules Status

OK

Green (solid)

the network interface is operating normally with error-free
operation. If the interface experiences alarms, the

OK

LED remains off.

Test

Yellow (solid)

the interface is operating in a test mode. This includes a
self-test, a test pattern, or a test loopback. When
illuminated, this LED also indicates that normal data flow
is not occurring on the module ports.

Error

Red (blink)

an error such as BPV (bipolar violation), OOF (out of
frame), or CRC (cyclic redundancy check) has occurred.

Alarm

Red (solid)

an alarm condition has been detected. When the alarm
condition is no longer valid, the

OK

LED illuminates. To

view an alarm condition, select the active alarm menu
item. If the alarm conditions have been corrected, you
can view the alarm which caused the activation of the

ALARM

LED in the system log.

«
...
27
28
29
30
31
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

Бренд: Calsense Страницы: 74

Бренд: IAI Страницы: 5

Бренд: Parker Страницы: 30

Compax3M Series

Бренд: Parker Страницы: 52

Бренд: Parker Страницы: 337

Бренд: Sartorius Страницы: 165

Бренд: Planar Страницы: 162

Бренд: THK Страницы: 134

Бренд: Sturtevant Richmont Страницы: 73

Latherm HZR Comfort

Бренд: LAMBERTI ELEKTRONIK Страницы: 16

Touch Screen Controller SX112

Бренд: 3M Страницы: 33

Бренд: Melexis Страницы: 13

Бренд: KEPCO Страницы: 34

agility AGY-101

Бренд: Fairford Страницы: 127

Бренд: ETI Страницы: 14

750-8202/040-000

Бренд: WAGO Страницы: 418

Touch Screen Controller EX112

Бренд: 3M Страницы: 40

Бренд: Texas Instruments Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды