ADTRAN ATLAS 550 Скачать руководство пользователя страница 181 | Manualshive

Страница: 181 / 412

background image

ATLAS 550 System Manual

Section 4 User Interface Guide

61200305L2-1B

© 2004 ADTRAN, Inc.

181

M

ODULES

(ADPCM-32) > S

TATUS

> S

TATUS

Read security: 5

Indicates the condition of the individual packet voice device. This field may display the following:

M

ODULES

(ADPCM-32) > S

TATUS

> A

LGORITHM

Read security: 5

Denotes the voice compression algorithm being used by the packet voice device. Voice data may be
encoded using any of a variety of compression algorithms or codecs. The codec for an individual call is
selected when the connection is configured. When ATLAS 550 assigns a packet voice device to a
particular call, the that packet voice devise is switched to the proper codec. Refer to the Frame Relay menu
section of this manual for more information.

M

ODULES

(ADPCM-32) > S

TATUS

> C

ONNECTION

Read security: 5

Helps identify a suspect packet voice device if a particular call reports poor quality. The displayed packet
identifier and the dial plan endpoint identify the call using this packet voice device.

M

ODULES

(ADPCM-32) > C

ONFIG

Write security: 4; Read security: 5

Provides diagnostic tools for suspected problems; under normal operation, users do not configure the
packet voice devices.

M

ODULES

(ADPCM-32) > C

ONFIG

> C

ONFIGURE

ADPCM-32 D

EVICES

Write security: 4; Read security: 5

Contains configuration parameters for individual ADPCM-32 devices.

N/A

This device is not populated on the selected 32 Channel ADPCM Resource
Module.

A

VAILABLE

This resource is available for voice compression and functioning properly.

P

ENDING

This resource is currently changing state.

B

USY

This resource is currently in use.

T

ESTING

This resource is currently being tested and is not available for use.

F

AILED

This resource has failed testing and is not available for use.

R

ELOADED

This resource was reinitialized after excessive errors.

Some voice compression standards may be used only under specific licensing
arrangements due to existing patents. The ATLAS 550 provides complete management of
these licensed resources; therefore, users are not required to take additional steps to
ensure conformance with licensing provisions. For example, the ATLAS 550 manages its
resources so users never exceed the maximum licensed number of simultaneous
connections.

«
...
179
180
181
182
183
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

Бренд: Eaton Страницы: 166

Бренд: Barthelme Страницы: 8

Бренд: Easy Heat Страницы: 4

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 4

GAT ACCESS 6100

Бренд: Gantner Страницы: 4

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: Rabbit Страницы: 12

Бренд: McIntosh Страницы: 68

Бренд: Linear Technology Страницы: 5

Alicat Scientific MC

Бренд: Halma Страницы: 2

TITAN Controls Saturn 4

Бренд: Sunlight Supply Страницы: 4

Бренд: VistaLab Страницы: 20

Keyboard Controller Series

Бренд: M-Audio Страницы: 2

Бренд: Powrmatic Страницы: 10

Бренд: TDSi Страницы: 23

WISE-2841 Series

Бренд: ICP DAS USA Страницы: 326

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды