ADTRAN ATLAS 550 Скачать руководство пользователя страница 121

Страница: 121 / 412

ATLAS 550 System Manual

Section 4 User Interface Guide

61200305L2-1B

121

ODULES

) > B

HANNEL

TATUS

> C

Read security: 5

(Channel) Displays the status of individual channels. The following symbols may display:

ODULES

) > P

ERFORMANCE

URRENT

Write security: 3; Read security: 5

The performance field provides status on key performance measures for the BRI interface. All fields
(except

ESET

) are read-only. The monitored parameters include the following:

ODULES

) > B

ONFIGURATION

Write security: 3; Read security: 5

All of the following configurable parameters apply to the BRI interface on the BRI DBU Network
Interface Module.

ODULES

) > B

ONFIGURATION

> P

Read security: 5

Displays the port number.

ODULES

) > B

ONFIGURATION

> P

ORT

AME

Write security: 3; Read security: 5

Accepts any alpha-numeric name up to 16 characters long, to uniquely identify the BRI interface on the
BRI DBU Network Interface Module.

ODULES

) > B

EST

Write security: 4; Read security: 5

The following options initiate tests and display test results.

Unallocated channel

Inactive channel

Active B channel

Active D channel

Displays the port number

ESET

Resets the NEBE and FEBE statistics

EBE

URRENT

Near-end block errors

EBE

URRENT

Far-end block errors

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды