manualshive.com logo in svg

Stoll CMS 730 S, Operating Instructions Manual

Share
Download
Stoll CMS 730 S Operating Instructions Manual Download Page 377

373

7 

 

Repairing the knitting machine 

7.4  Eliminating faults in electronics system 

7.4.4

Replacing electronic card

1. Set main switch to "0" and wait until the LEDs on the power supply unit 

go out (approx. 60 seconds).

2. Open the cover of the left control cabinet.

3. Remove the card.

4. Plug in the new card.

5. Close the cover of the left control cabinet.

6. Set the main switch to "1" and acknowledge the error remedy.

CAUTION

An electronic card can be destroyed by electrostatic 
charge!

If you touch a board while you are electrostatically charged, 
the board will be destroyed.

➜

First discharge yourself by touching "ground", e.g. a 
water pipe or the machine frame, then touch a card.

➜

Only touch cards on the edge or the front side.

CAUTION

The electronic boards can be damaged by damage to the 
pins on the rear of the board!

If the pins of the cards are bent or broken off at the rear, new 
cards must be used.

➜

When replacing the cards, make sure that the pins are 
not damaged.

Summary of Contents for CMS 730 S





















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands