Stoll CMS 730 S Operating Instructions Manual Download Page 370

Page: 370 / 468

Repairing the knitting machine

Replacing parts 7.3

366

7.3.14

Replacing drive belts and friction roller of friction feed
wheel

The drive belts and the friction roller of the friction feed wheel are replaced
with the following steps:



Preparations



Replace the drive belt



Change position of friction roller



Replacing the friction roller

Preparations

1. Remove the lug (1) by loosening the knurled screws somewhat.



Friction feed wheel

2. Remove screws (2) and take off the stop motion rails.

3. Release the couplings of the arms (3) so that they can swing downward.

4. Remove the screws (4) and take off the housing cover (5).

Replace the drive belt

1. Turn the V-ribbed belt pulley (6) by hand until both Allen screws can be

released through the holes (7).



Drive belt

2. Remove the belt (8).

Summary of Contents for CMS 730 S





















































































































































































































































































































































































































































































Search results

Summary of Contents for CMS 730 S

Reviews:

Brands by name

Popular brands

Stoll CMS 730 S, Operating Instructions Manual

Search results

Summary of Contents for CMS 730 S

Reviews:

Brands by name

Popular brands