manualshive.com logo in svg

Stoll CMS 730 S, Operating Instructions Manual

Share
Download
Stoll CMS 730 S Operating Instructions Manual Download Page 376

Repairing the knitting machine  

7 

Eliminating faults in electronics system  7.4 

372

7.4.2

Power supply unit

Power supply unit

The LEDs on the power supply unit indicate which voltages are generated 
and at which voltage an error occurs. While switching on the main switch, 
the lower three LEDs light up immediately, and the +28 V approx. 1 second 
later, followed by the +40 V. The order in which the LEDs light up when 
switching on may provide information on fault causes.

7.4.3

Control of yarn carrier magnets

Each knitting system has got an electronic board (1) for controlling yarn 
carrier magnets.

Electronic cards for controlling yarn carrier magnets

   

Card

Function

960

(ID 300 960)

Activating of the yarn carrier magnets after the time for switching 
the yarn carrier magnets has been announced by the board 966.

Electronic cards

Summary of Contents for CMS 730 S





















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands