RKC INSTRUMENT Z-TIO-G, Instruction Manual, Page: 99 / 246

8. COMMUNICATION DATA LIST
IMS01T28-E4
8-17
Continued from the previous page.
No. Name
Iden-
tifier
Chan-
nel
Register address
Digits
Attri-
bute
Struc-
ture
Data range
Factory
set value
HEX DEC
51 Derivative gain DG CH1
CH2
0242
0243 578
579 7 R/W * C 0.1 to 10.0 6.0
52
ON/OFF action
differential gap
(upper) IV CH1
CH2
0246
0247 582
583 7 R/W * C RTD input:
0 (0.0, 0.00) to Input span
(Unit:

C)
Varies with the setting of the decimal
point position. However, even if "3:
Three decimal places" is set, the
maximum settable decimal places are 2.
Voltage (V) input:
0.00 to 100.00 % of input span
RTD input:
1.00
V input:
1.00
53
ON/OFF action
differential gap
(lower) IW CH1
CH2
024A
024B 586
587 7 R/W * C RTD input:
1.00
V input:
1.00
54
Action (high) at input
error WH CH1
CH2
024E
024F 590
591 1 R/W * C 0: Normal control
1: Manipulated output value at
input
error
0
55
Action (low) at input
error WL CH1
CH2
0252
0253 594
595 1 R/W * C 0
56
Manipulated output
value at input error OE CH1
CH2
0256
0257 598
599 7 R/W * C

105.0 to

105.0 %
Actual output values become those
restricted by the output limiter.
0.0
57
Manipulated output
value at STOP mode OF CH1
CH2
025A
025B 602
603 7 R/W * C

5.0 to

105.0 %

5.0
58
Output change rate
limiter (up) PH CH1
CH2
0262
0263 610
611 7 R/W * C 0.0 to 100.0 % of manipulated
output/seconds
(0.0: OFF)
0.0
59
Output change rate
limiter (down) PL CH1
CH2
0266
0267 614
615 7 R/W * C 0.0
60
Output limiter high OH CH1
CH2 026A
026B 618
619 7 R/W C Output limiter low to 105.0 % 105.0
61 Output limiter low OL CH1
CH2 026E
026F 622
623 7 R/W C

5.0 % to Output limiter high

5.0
62
AT bias GB CH1
CH2 0282
0283 642
643 7 R/W * C

Input span to +Input span
Varies with the setting of the decimal
point position. However, even if "3:
Three decimal places" is set, the
maximum settable decimal places are 2.
When the AT point exceeds the setting
range, high (or low) limit of the setting
range becomes the AT point.
0.00
63
AT cycles G3 CH1
CH2 0286
0287 646
647 1 R/W * C 0: 1.5 cycles
1: 2.0 cycles
2: 2.5 cycles
3: 3.0 cycles
1
64 Output value with AT
turned on OP CH1
CH2
028A
028B 650
651 7 R/W * C Output value with AT turned off to

105.0 %
Actual output values become those
restricted by the output limiter.
105.0
65
Output value with AT
turned off OQ CH1
CH2
028E
028F 654
655 7 R/W * C

105.0 % to Output value with AT
turned on
Actual output values become those
restricted by the output limiter.

105.0
66
AT differential gap
time
GH CH1
CH2
0292
0293 658
659 7 R/W * C 0.0 to 50.0 seconds 10.0
67 Proportional band
adjusting factor KC CH1
CH2
0296
0297 662
663 7 R/W * C 0.01 to 10.00 times 1.00
68
Integral time
adjusting factor KD CH1
CH2
029A
029B 666
667 7 R/W * C 0.01 to 10.00 times 1.00
69 Derivative time
adjusting factor KE CH1
CH2
029E
029F 670
671 7 R/W * C 0.01 to 10.00 times 1.00
* During RUN (control), the attribute of Engineering setting data is RO. To configure Engineering setting data, the RUN/STOP switch must
be set to STOP (control stopped).
Continued on the next page.