RKC INSTRUMENT Z-TIO-G, Instruction Manual, Page: 100 / 246

8. COMMUNICATION DATA LIST
IMS01T28-E4
8-18
Continued from the previous page.
No. Name
Iden-
tifier
Chan-
nel
Register address
Digits
Attri-
bute
Struc-
ture
Data range
Factory
set value
HEX DEC
70 Proportional band
limiter (high)
P6 CH1
CH2
02AE
02AF 686
687 7 R/W * C RTD input:
0 (0.0, 0.00) to Input span
(Unit:

C)
Varies with the setting of the decimal
point position. However, even if "3:
Three decimal places" is set, the
maximum settable decimal places are 2.
Voltage (V) input:
0.00 to 300.00 % of input span
0 (0.0, 0.00): ON/OFF action
RTD input:
Input span
V input:
300.00
71 Proportional band
limiter (low)
P7 CH1
CH2
02B2
02B3 690
691 7 R/W * C RTD input:
0.00
V input:
0.00
72 Integral time limiter
(high)
I6 CH1
CH2
02B6
02B7 694
695 7 R/W * C 0.0 to 3000.0 seconds
(0.0: PD action)
3000.0
73 Integral time limiter
(low)
I7 CH1
CH2
02BA
02BB 698
699 7 R/W * C 0.0 to 3000.0 seconds
(0.0: PD action)
0.0
74 Derivative time limiter
(high)
D6 CH1
CH2
02BE
02BF 702
703 7 R/W * C 0.0 to 3000.0 seconds
(0.0: PI action)
3000.0
75 Derivative time limiter
(low)
D7 CH1
CH2
02C2
02C3 706
707 7 R/W * C 0.0 to 3000.0 seconds
(0.0: PI action)
0.0
76 Setting change rate
limiter unit time
HU CH1
CH2
031E
031F 798
799 7 R/W * C 1 to 3600 seconds
60
77 Soak time unit RU CH1
CH2 0322
0323 802
803 1 R/W * C

RKC communication
0: 0:00 to 99:59 (hrs:min)
[0 hours 00 minutes to 99 hours
59 minutes]
1: 0:00 to 199:59 (min:sec)
[0 minutes 00 seconds to 199
minutes 59 seconds]

Modbus
0: 0 to 5999 minutes
[0 hours 00 minutes to
99 hours 59 minutes]
1: 0 to 11999 seconds
[0 minutes 00 seconds to
199 minutes 59 seconds]
Set the data range of Memory area soak
time monitor and Area soak time.
1
78 Setting limiter high SH CH1
CH2 0326
0327 806
807 7 R/W * C Setting limiter low to Input scale
high
Varies with the setting of the decimal
point position. However, even if "3:
Three decimal places" is set, the
maximum settable decimal places are 2.
Input scale
high
79 Setting limiter low SL CH1
CH2 032A
032B 810
811 7 R/W * C Input scale low to Setting limiter
high
Varies with the setting of the decimal
point position. However, even if "3:
Three decimal places" is set, the
maximum settable decimal places are 2.
Input scale
low
80 PV transfer function TS CH1
CH2 032E
032F 814
815 1 R/W * C 0: Unused
1: Used
0
81 Operation mode
assignment 1
(Logic output selection
function)
Logic output 1 to 4
EA CH1
CH2
0332
0333 818
819 7 R/W * C 0: No assignment
1: Operation mode
(Monitor/Control)
2: Operation mode
(Monitor

Event function/Control)
3: Auto/Manual
4: Remote/Local
5: Unused (Do not set this one.)
0
* During RUN (control), the attribute of Engineering setting data is RO. To configure Engineering setting data, the RUN/STOP switch must
be set to STOP (control stopped).
Continued on the next page.