Omron NT - SUPPORT TOOL FOR WINDOWS V4 Operation Manual Download Page 423

Page: 423 / 573

10-1

Section

Quick Reference

412

Item

Operation

Refer to

PC (PLC)
Bit Status
Display

To turn a lamp ON/OFF
according to the ON/OFF
status of a PC (PLC) bit
that is controlled by the
operation of touch
switches.

(1) [Objects]

→

[Touch Switch]

→

[Function: Notify Bit]

Reflect the touch switch status in the PC (PLC) bit sta-
tus.

(2) [Objects]

→

[Lamp]

→

[Standard]

Reflect the PC (PLC) bit status at the lamp.

6-8-1

6-5-1

To switch the graphic to
be displayed according to
the PC (PLC) bit status

(1) [Tools]

→

[Image Editor]

[Tools]

→

[Library Editor]

Create the image data or the library data.

(2) [Objects]

→

[Lamp]

→

[Image]

Create an image/library lamp.

Set the light function PC (PLC) address.

Screen

PC
(PLC)

Bit

If ON

If OFF

Graphic (image data)

8-1

8-2

6-5-2

To switch the text to be
displayed according to the
PC (PLC) bit status.

(1) [Objects]

→

[Lamp] or [Touch Switch]

Create a lamp or a touch switch for which On Off Static
is set as the label type

(2) Turn the PC (PLC) bit to which the lamp is allocated

ON/OFF

DEF

Screen

ABC

Bit

If ON

If OFF

Lamp or touch switch with On Off static label

PC
(PLC)

(Only for NT21, NT31/631-V2 and above)

8-2

6-5-2

(1) [Tools] – [Library Editor]

(2) [Objects]

→

[Lamp]

→

[Image]

Create a lamp that displays the registered text.

(3) Turn the PC (PLC) bit allocated to the lamp ON/OFF.

DEF

Screen

ABC

Bit

If ON

If OFF

Image

PC
(PLC)

8-2

6-5-2

Summary of Contents for NT - SUPPORT TOOL FOR WINDOWS V4






























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for NT - SUPPORT TOOL FOR WINDOWS V4

Reviews:

Related manuals for NT - SUPPORT TOOL FOR WINDOWS V4

Brands by name

Popular brands

Omron NT - SUPPORT TOOL FOR WINDOWS V4, Operation Manual

Search results

Summary of Contents for NT - SUPPORT TOOL FOR WINDOWS V4

Reviews:

Related manuals for NT - SUPPORT TOOL FOR WINDOWS V4

Brands by name

Popular brands