Omron NT - SUPPORT TOOL FOR WINDOWS V4 Operation Manual Download Page 390

Page: 390 / 573

9-3

Section

Creating the Sample Data

378

General

Position

––

Size

––

Frame

Shape

3-Dimension

Show ON State

Color

Frame

White

OFF

Transparent

Settings

Function

Switch Screen

Screen No.

Light
Function

Address

PC (PLC) Address

––

Function

I/O Comments

––

Lamp Attribute

Attribute

Light

Label

, Menu (refer

to the following)

*1:

Press

to set the label.

After completing the setting, go to the next step without clicking on

button.

Setting the label of [Menu] button

(4) Press

in the general property of a touch switch and set the la-

bel properties as shown below.

Description

Position

––

Font Type

Standard

Scale

1 (Equal)

Smoothing

––

Attribute

Standard

Color

Foreground

White

Background

Transparent

Reference: With the NT21, NT31, NT31C, NT631 and NT631C, “Color: ON” and “Color:

OFF” can be set independently for a label so that the lamp can be displayed in
different colors in the ON and OFF states.

Click on

, (returns to touch switch property) then click on

again.

Adjusting the size and position of the touch switch

(5) Specify the [Menu] button and select [Edit] (menu bar)

→

[Edit Object].

(6) Adjust the size and position of [Menu] button frame.

(7) Adjust the position of label “Menu” by dragging it.

Summary of Contents for NT - SUPPORT TOOL FOR WINDOWS V4






























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for NT - SUPPORT TOOL FOR WINDOWS V4

Reviews:

Related manuals for NT - SUPPORT TOOL FOR WINDOWS V4

Brands by name

Popular brands

Omron NT - SUPPORT TOOL FOR WINDOWS V4, Operation Manual

Search results

Summary of Contents for NT - SUPPORT TOOL FOR WINDOWS V4

Reviews:

Related manuals for NT - SUPPORT TOOL FOR WINDOWS V4

Brands by name

Popular brands