Omron NT - SUPPORT TOOL FOR WINDOWS V4 Operation Manual Download Page 256

Page: 256 / 573

6-9

Section

Graphs

243

Note that specification for –100% is valid only when [Display Sign] is selected.

Guidance

Following types of trend graph element are provided.

0% to 100% display

Direction: Right

Direction: Left

Direction: Up

Direction: Down

→

Time

↑

Time

←

Time

↓

Time

–100% to 100% display

Direction: Right

Direction: Left

Direction: Up

Direction: Down

→

Time

↑

Time

←

Time

↓

Time

Which of [0 to 100%] and [–100 to 100%] trend graphs is displayed should be
selected with the setting for [Display Sign] in the general attributes.

Check mark set:

–100 to 100% display

Check mark not set: 0 to 100% display

The following two types of trend graph display are provided.

Standard:

The latest drawing position moves in the direction set for [Direc-
tion].

Present
drawing
position

Next
drawing
position

Summary of Contents for NT - SUPPORT TOOL FOR WINDOWS V4






























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for NT - SUPPORT TOOL FOR WINDOWS V4

Reviews:

Related manuals for NT - SUPPORT TOOL FOR WINDOWS V4

Brands by name

Popular brands

Omron NT - SUPPORT TOOL FOR WINDOWS V4, Operation Manual

Search results

Summary of Contents for NT - SUPPORT TOOL FOR WINDOWS V4

Reviews:

Related manuals for NT - SUPPORT TOOL FOR WINDOWS V4

Brands by name

Popular brands