manualshive.com logo in svg

NXP Semiconductors LPC43Sxx, User Manual

Share
Download
NXP Semiconductors LPC43Sxx User Manual Download Page 326

UM10503

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2015. All rights reserved.

User manual

Rev. 2.1 — 10 December 2015 

326 of 1441

NXP Semiconductors

UM10503

Chapter 16: LPC43xx/LPC43Sxx Pin configuration

P9_5

M9

-

[2]

I; PU -

R — 

Function reserved.

O

MCOA1 — 

Motor control PWM channel 1, output A.

O

USB1_VBUS_EN — 

USB1 VBUS power enable.

-

R — 

Function reserved.

I/O

GPIO5[18] — 

General purpose digital input/output pin.

O

ENET_TXD3 — 

Ethernet transmit data 3 (MII interface).

I/O

SGPIO3 — 

General purpose digital input/output pin.

O

U0_TXD — 

Transmitter output for USART0.

P9_6

L11

-

[2]

I; PU I/O

GPIO4[11] — 

General purpose digital input/output pin.

O

MCOB1 — 

Motor control PWM channel 1, output B.

I

USB1_PWR_FAULT — 

USB1 Port power fault signal indicating over-current 

condition; this signal monitors over-current on the USB1 bus (external 
circuitry required to detect over-current condition).

-

R — 

Function reserved.

-

R — 

Function reserved.

I

ENET_COL — 

Ethernet Collision detect (MII interface).

I/O

SGPIO8 — 

General purpose digital input/output pin.

I

U0_RXD — 

Receiver input for USART0.

PA_0

L12

-

[2]

I; PU -

R — 

Function reserved.

-

R — 

Function reserved.

-

R — 

Function reserved.

-

R — 

Function reserved.

-

R — 

Function reserved.

O

I2S1_RX_MCLK — 

I2S1 receive master clock.

O

CGU_OUT1 — 

CGU spare clock output 1.

-

R — 

Function reserved.

PA_1

J14

-

[3]

I; PU I/O

GPIO4[8] — 

General purpose digital input/output pin.

I

QEI_IDX — 

Quadrature Encoder Interface INDEX input.

-

R — 

Function reserved.

O

U2_TXD — 

Transmitter output for USART2.

-

R — 

Function reserved.

-

R — 

Function reserved.

-

R — 

Function reserved.

-

R — 

Function reserved.

Table 186. LPC4370/LPC43S70 Pin description

 …continued

LCD is not available on all parts. 

Symbol

LB

GA25

6

TFBGA100

R

e

se

t st

ate

[1

]

Ty

p

e

Description

Summary of Contents for LPC43Sxx


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands