manualshive.com logo in svg

NEC V850E/RS1, User Manual, Page: 312 / 852

Share
Download
NEC V850E/RS1 User Manual Download Page 312

312

Chapter 8

16-Bit Timer/Event Counter Q

User’s Manual U16702EE3V2UD00

(2)

Timer Q control register 1 (TQnCTL1)

The TQnCTL1 register is an 8-bit register that controls the operation of timer Q.
This register can be read or written in 8-bit or 1-bit units.
RESET input clears this register to 00H.

Figure 8-8:

Timer Q Control Register 1 (TQnCTL1) Format (1/2) 

Caution:

In the synchronous operation mode, the master macro can be set only in the PWM
mode, external trigger pulse output mode, pulse output mode, and free-running
mode.
The slave macros can be set only in the free-running mode.
Setting the external event count mode, one-shot pulse mode, and pulse width 
measurement mode is prohibited.

Symbol

7

6

5

4

3

2

1

0

Address

R/W

After

reset

TQ0CTL1 TQ0SYE TQ0EST TQ0EEE

0

0

TQ0MD2 TQ0MD1 TQ0MD0

FFFFF541H R/W 00H

Symbol

7

6

5

4

3

2

1

0

Address

R/W

After

reset

TQ1CTL1 TQ1SYE TQ1EST TQ1EEE

0

0

TQ1MD2 TQ1MD1 TQ1MD0

FFFFF611H R/W 00H

TQnSYE

Tuned operation mode enable control

0

Independent operation mode (asynchronous operation mode)

1

Tuned operation mode (specification of slave operation)
In this mode, timer Q can operate in synchronization with a master timer.

Master timer

Slave timer

TMQ0

TMQ1

-

For the tuned operation mode, refer to 

8.6 Timer Synchronized Operation Function

. 

Caution:

Be sure to clear the TQ0SYE bit to 0 (master timer) and TQ1SYE bit to 1
(slave timer)

TQnEST

Software trigger control

0

No operation

1

In one-shot pulse mode: One-shot pulse software trigger

In external trigger pulse output mode: Pulse output software trigger

The TQnEST bit functions as a software trigger in the one-shot pulse mode or external trigger pulse 
output mode (this bit is invalid in any other mode). By setting TQnEST to 1 when TQnCE = 1, a software 
trigger is issued. Therefore, be sure to set TQnEST to 1 when TQnCE = 1.
The TIQn0 pin is used for an external trigger. The read value of the TQnEST bit is always 0.

Downloaded from 

Elcodis.com

 

electronic components distributor

 

Summary of Contents for V850E/RS1





















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments