manualshive.com logo in svg

Hitachi HD6417032, Hardware Manual

The "Hitachi HD6417032" Hardware Manual is available for free download on our website. This comprehensive manual provides detailed instructions on operating, maintaining, and troubleshooting the HD6417032, ensuring that users have the necessary information to fully utilize this product. Download your manual now from manualshive.com!

Share
Download
background image

187

• 

Bit 2 (Address Error Flag Bit (AE)): AE indicates that an address error has occurred in the
DMAC. When this flag is set to 1, the channel cannot be enabled even if the DE bit in the
DMA channel control register (CHCR) and the DME bit are set to 1. To clear the AE bit, read
1 from it and then write 0. It is initialized to 0 by a reset and in standby mode.

Bit 2: AE

Description

0

No DMAC address error 

(Initial value)

To clear the AE bit, read 1 from it and then write 0

1

Address error by DMAC

• 

Bit 1 (NMI Flag Bit (NMIF)): NMIF indicates that an NMI interrupt has occurred. When this
flag is set to 1, the channel cannot be enabled even if the DE bit in CHCR and the DME bit are
set to 1. To clear the NMIF bit, read 1 from it and then write 0. It is initialized to 0 by a reset
and in standby mode.

Bit 1: NMIF

Description

0

No NMI interrupt 

(Initial value)

To clear the NMIF bit, read 1 from it and then write 0

1

NMI has occurred

• 

Bit 0 (DMA Master Enable Bit (DME)): DME enables or disables DMA transfers on all
channels. A channel becomes enabled for a DMA transfer when the DE bit in each DMA's
CHCR and the DME bit are set to 1. For this to be effective, however, the TE bit of each
CHCR and the NMIF and AE bits must all be 0. When the DME bit is cleared, all channel
DMA transfers are aborted.

Bit 0: DME

Description

0

DMA transfers disabled on all channels 

(Initial value)

1

DMA transfers enabled on all channels

Summary of Contents for HD6417032



















































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HD6417032

Paradyne Hotwire 5446 Notice preview
Hotwire 5446
Brand: Paradyne Pages: 2
M86 Security R3000 Series Evaluation Manual preview
R3000 Series
Brand: M86 Security Pages: 46
Renesas Asynchronous SH7145F Application Note preview
Asynchronous SH7145F
Brand: Renesas Pages: 17
ekwb EK-FC1080 GTX Ti TF6 Installation Manual preview
EK-FC1080 GTX Ti TF6
Brand: ekwb Pages: 2
Altera Nios II Hardware Development Manual preview
Nios II
Brand: Altera Pages: 42
C&T Solution RCO-3000 Series User Manual preview
RCO-3000 Series
Brand: C&T Solution Pages: 96
Qlogic Storage Networking (Unified Fabric Pilot) Installation Manual preview
Storage Networking (Unified Fabric Pilot)
Brand: Qlogic Pages: 76
RANA Systems RanaSystems 13-0010--001 User Manual preview
RanaSystems 13-0010--001
Brand: RANA Systems Pages: 328
SYNTEK STA-UI-A0035 User Manual preview
STA-UI-A0035
Brand: SYNTEK Pages: 41
National Instruments NI 447 Series User Manual preview
NI 447 Series
Brand: National Instruments Pages: 80
Advantech SOM-C350 User Manual preview
SOM-C350
Brand: Advantech Pages: 108
Patton electronics ipRocketLink IAD 3086 Quick Start Manual preview
ipRocketLink IAD 3086
Brand: Patton electronics Pages: 12
FiberHome AN5506-04-F User Manual preview
AN5506-04-F
Brand: FiberHome Pages: 2
Net Optics Phantom HD Quick Install Manual preview
Phantom HD
Brand: Net Optics Pages: 2
Microchip Technology PD-9501-10GCO/AC User'S Installation Manual preview
PD-9501-10GCO/AC
Brand: Microchip Technology Pages: 41
Wistron NeWeb DNBA-81 User Manual preview
DNBA-81
Brand: Wistron NeWeb Pages: 32
Balluff BIS C-489-1 KBT02 Series Technical Manual preview
BIS C-489-1 KBT02 Series
Brand: Balluff Pages: 74
Cypress Semiconductor CY7C1440AV33 Specification Sheet preview
CY7C1440AV33
Brand: Cypress Semiconductor Pages: 31

Brands by name

Popular brands

Load more brands