Hitachi HD6417032 Hardware Manual Download Page 170 | Manualshive

Page: 170 / 690

background image

135

Area 7: Area 7 is an area with address bits A26–A24 set to 111 and an address range of
H'7000000–H'7FFFFFF and H'F000000–H'FFFFFFF. Figure 8.10 shows a memory map of area 7.

Area 7 is allocated to external memory space when A27 is 0 and on-chip RAM space when A27 is
1. In external memory space, the bus width is 8 bits. The A23 and A22 bits are not output and the
shadow is in 4-Mbyte units. When external memory is accessed, the

CS7

signal is valid.

The on-chip RAM space has a bus width of 32 bits. In the SH7032, the on-chip RAM capacity is 8
kbytes, so A23–A13 are ignored and the shadows are in 8-kbyte units. In the SH7034, the on-chip
RAM capacity is 4 kbytes, so A23–A12 are ignored and the shadows are in 4-kbyte units. During
on-chip RAM access, the

CS7

signal is not valid.

H'7000000

H'7400000

H'7800000

H'7C00000

H'73FFFFF

H'77FFFFF

H'7BFFFFF

H'7FFFFFF

Shadow

Shadow

Shadow

Shadow

External

memory

space

(4 Mbytes)

H'F000000

H'FFFFFFF

Shadow

Shadow

Shadow

Shadow

Shadow

Shadow

H'FFFF000 (SH7034)

H'F000FFF (SH7034)

H'FFFE000 (SH7032)

H'F001FFF (SH7032)

Logical address

space

Logical address

space

Actual

space

Actual

space

8-bit space

32-bit space

• On-chip
RAM space
SH7032:
8 kbytes,
SH7034:
4 kbytes
• Valid
addresses
SH7032:
A12–A0
(A23–A13
not output)
SH7034:
A11–A0
(A23–A12
not output)
•

CS7

not

valid

• Valid
addresses
A21–A0
(A23 and A22
not output)
•

CS7

valid

Figure 8 10 Memory Map of Area 7

«
...
168
169
170
171
172
...
»

Summary of Contents for HD6417032



















































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HD6417032

Express EtherNetwork DFE-670TXD

Brand: D-Link Pages: 4

Brand: DAD Pages: 36

Brand: D-Link Pages: 2

Brand: GE Pages: 146

Brand: VMIC Pages: 126

Duinotech Lilypad Plus XC3920

Brand: Jaycar Electronics Pages: 2

Brand: Cisco MERAKI Pages: 4

Brand: VCS Pages: 118

Brand: Observint Pages: 117

Brand: Cypress Semiconductor Pages: 26

Brand: MCT Pages: 12

Protection Board R0E330850ACBP0

Brand: Renesas Pages: 8

Brand: Camozzi Pages: 22

Brand: RAK Pages: 14

Brand: Z3 Technology Pages: 83

Brand: Cognex Pages: 57

Brand: Planet Pages: 38

Brand: Hanwha Vision Pages: 131

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands