manualshive.com logo in svg

Hitachi HD6417032, Hardware Manual

The "Hitachi HD6417032" Hardware Manual is available for free download on our website. This comprehensive manual provides detailed instructions on operating, maintaining, and troubleshooting the HD6417032, ensuring that users have the necessary information to fully utilize this product. Download your manual now from manualshive.com!

Share
Download
background image

361

Bit 5: ORER

Description

0

Receiving is in progress or has ended normally

*

1

(Initial value)

ORER is cleared to 0 when:

• 

The chip is reset or enters standby mode

• 

Software reads ORER after it has been set to 1, then writes 0 in ORER

1

A receive overrun error occurred

*

2

ORER is set to 1 if reception of the next serial data ends when RDRF is set to 1

Notes:

*

1 Clearing the RE bit to 0 in the serial control register does not affect the ORER bit, which

retains its previous value.

*

2 RDR continues to hold the data received before the overrun error, so subsequent

receive data is lost. Serial receiving cannot continue while ORER is set to 1. In
synchronous mode, serial transmitting is disabled.

• 

Bit 4 (Framing Error (FER)): FER indicates that data reception ended abnormally due to a
framing error in the asynchronous mode.

Bit 4: FER

Description

0

Receiving is in progress or has ended normally

(Initial value)

Clearing the RE bit to 0 in the serial control register does not affect the FER bit,
which retains its previous value.

FER is cleared to 0 when:

• 

The chip is reset or enters standby mode

• 

Software reads FER after it has been set to 1, then writes 0 in FER

1

A receive framing error occurred. When the stop bit length is two bits, only the
first bit is checked. The second stop bit is not checked. When a framing error
occurs, the SCI transfers the receive data into RDR but does not set RDRF.
Serial receiving cannot continue while FER is set to 1. In synchronous mode,
serial transmitting is also disabled.

FER is set to 1 if the stop bit at the end of receive data is checked and found to
be 0.

• 

Bit 3 (Parity Error (PER)): PER indicates that data reception (with parity) ended abnormally
due to a parity error in asynchronous mode.

Summary of Contents for HD6417032



















































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HD6417032

Novus NVIP- NVRA0104/GO User Manual preview
NVIP- NVRA0104/GO
Brand: Novus Pages: 44
TDK HHM Series HHM2411 Specification Sheet preview
HHM Series HHM2411
Brand: TDK Pages: 2
Cytron Technologies SHIELD-2AMOTOR User Manual preview
SHIELD-2AMOTOR
Brand: Cytron Technologies Pages: 13
IBM 2740-1 System Reference Manual preview
2740-1
Brand: IBM Pages: 64
Patton electronics ipRocketLink IAD 3086 Quick Start Manual preview
ipRocketLink IAD 3086
Brand: Patton electronics Pages: 12
Idis DR-2308P Quick Manual preview
DR-2308P
Brand: Idis Pages: 18
TANDBERG 240LTO Quick Start Manual preview
240LTO
Brand: TANDBERG Pages: 2
Radica Games DAVID-II 716 Operating And Maintenance Instruction Manual preview
DAVID-II 716
Brand: Radica Games Pages: 40
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Brand: Airvana Pages: 90
Renesas HD74HCT1G04 Datasheet preview
HD74HCT1G04
Brand: Renesas Pages: 8
Broadband Products Xtreme Networked Boat User Manual preview
Xtreme Networked Boat
Brand: Broadband Products Pages: 16
A4Tech G6 Saver User Manual preview
G6 Saver
Brand: A4Tech Pages: 8
G&D DP1.2-Vision-IP-Fiber Installation And Operation Manual preview
DP1.2-Vision-IP-Fiber
Brand: G&D Pages: 240
ZALMAN CNPS9900 Max User Manual preview
CNPS9900 Max
Brand: ZALMAN Pages: 9
Divio NRM 311 User Manual preview
NRM 311
Brand: Divio Pages: 78
Crestron 2 Channel Inductor Module CLX-2IND Specification Sheet preview
2 Channel Inductor Module CLX-2IND
Brand: Crestron Pages: 1
Crestron HZA-PWR-15A Quick Start preview
HZA-PWR-15A
Brand: Crestron Pages: 2
Lenze II EPZ-10202 Instructions Manual preview
II EPZ-10202
Brand: Lenze Pages: 15

Brands by name

Popular brands

Load more brands