manualshive.com logo in svg

Hitachi HD6417032, Hardware Manual

The "Hitachi HD6417032" Hardware Manual is available for free download on our website. This comprehensive manual provides detailed instructions on operating, maintaining, and troubleshooting the HD6417032, ensuring that users have the necessary information to fully utilize this product. Download your manual now from manualshive.com!

Share
Download
background image

116

Bit 12: BE

Description

0

Normal mode: full access 

(Initial value)

1

Burst operation: high-speed page mode

• 

Bit 11 (CAS Duty (CDTY)): CDTY selects 35% or 50% of the TC state as the high-level duty
ratio of the signal 

CAS

 in short-pitch access. When cleared to 0, the 

CAS

 signal high level

duty is 50%; when set to 1, it is 35%.

Bit 11: CDTY

Description

0

CAS

 signal high level duty cycle is 50% of the T

C

 state  (Initial value)

1

CAS

 signal high level duty cycle is 35% of the T

C

 state

• 

Bit 10 (Multiplex Enable Bit (MXE)): MXE determines whether or not DRAM row and
column addresses are multiplexed. When cleared to 0, addresses are not multiplexed; when set
to 1, they are multiplexed.

Bit 10: MXE

Description

0

Multiplexing of row and column addresses disabled 

(Initial value)

1

Multiplexing of row and column addresses enabled

• 

Bits 9 and 8 (Multiplex Shift Count 1 and 0 (MXC1 and MXC0)): Shift row addresses
downward by a certain number of bits (8–10) when row and column addresses are multiplexed
(MXE = 1). Regardless of the MXE bit setting, these bits also select the range of row addresses
compared in burst operation.

Bit 9:
MXC1

Bit 8:
MXC0

Row Address Shift
(MXE = 1)

Row Address Bits Compared
(in Burst Operation) (MXE = 0 or 1)

0

0

8 bits

(Initial value)

A8–A27

(Initial value)

1

9 bits

A9–A27

1

0

10 bits

A10–A27

1

Reserved

Reserved

• 

Bits 7–0 (Reserved): These bits are always read as 0. The write value should always be 0.

Summary of Contents for HD6417032



















































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HD6417032

Data Translation DT330 Series Getting Started Manual preview
DT330 Series
Brand: Data Translation Pages: 60
IEI Technology KINO-KBN-i2 Quick Installation Manual preview
KINO-KBN-i2
Brand: IEI Technology Pages: 21
Patton electronics RocketLink-G 3088/I Getting Started Manual preview
RocketLink-G 3088/I
Brand: Patton electronics Pages: 61
TC Electronic DB6 User Manual preview
DB6
Brand: TC Electronic Pages: 174
TC Electronic Finalizer Express User Manual preview
Finalizer Express
Brand: TC Electronic Pages: 33
XIA Pixie-4 Express Software Manual preview
Pixie-4 Express
Brand: XIA Pages: 17
Dazzle Hollywood DV-Bridge User Manual preview
Hollywood DV-Bridge
Brand: Dazzle Pages: 63
AXIOMTEK eBOX532-100-FL Series Quick Installation Manual preview
eBOX532-100-FL Series
Brand: AXIOMTEK Pages: 2
IDT USB-BRIDGEV2-EVAL Evaluation Board Manual preview
USB-BRIDGEV2-EVAL
Brand: IDT Pages: 11
A4Tech RG-71M User Manual preview
RG-71M
Brand: A4Tech Pages: 7
Z Microsystems TranzStor 8X User Manual preview
TranzStor 8X
Brand: Z Microsystems Pages: 51
Intel IXP45X Developer'S Manual preview
IXP45X
Brand: Intel Pages: 958
Patton electronics FORESIGHT 6300 User Manual preview
FORESIGHT 6300
Brand: Patton electronics Pages: 145
Wyse C90LE7 Quick Start Manual preview
C90LE7
Brand: Wyse Pages: 8
IBM 2740-1 System Reference Manual preview
2740-1
Brand: IBM Pages: 64
Taiwan Commate Computer Inc. P2BXA-V Quick Installation preview
P2BXA-V
Brand: Taiwan Commate Computer Inc. Pages: 25
Greenlee 910FS Instruction Manual preview
910FS
Brand: Greenlee Pages: 52
Wistron NeWeb DNBA-81 User Manual preview
DNBA-81
Brand: Wistron NeWeb Pages: 32

Brands by name

Popular brands

Load more brands