manualshive.com logo in svg

Hitachi HD6417032, Hardware Manual

The "Hitachi HD6417032" Hardware Manual is available for free download on our website. This comprehensive manual provides detailed instructions on operating, maintaining, and troubleshooting the HD6417032, ensuring that users have the necessary information to fully utilize this product. Download your manual now from manualshive.com!

Share
Download
background image

132

Areas 2–4 are always used as external memory space. The bus width is 8 bits when the A27 bit is
0 and 16 bits when it is 1. A23 and A22 bits are not output and the shadow is in 4-Mbyte units.
When areas 2–4 are accessed, the 

CS2

, 

CS3

, and 

CS4

 signals are valid. Area 2 has a long wait

function, so between 1 and 4 states can be selected for the number of long waits inserted into the
bus cycle using bits A02LW1 and A02LW0 in WCR3.

H'A000000

H'A3FFFFF

H'A400000

H'A7FFFFF

H'A800000

H'ABFFFFF

H'AC00000

H'AFFFFFF

H'2000000

H'2400000

H'2800000

H'2C00000

H'23FFFFF

H'27FFFFF

H'2BFFFFF

H'2FFFFFF

Shadow

Shadow

Shadow

Shadow

External

memory space

(4 Mbytes)

Logical address space

16-bit space

8-bit space

Actual space

• Valid addresses A21–A0
  (A23 and A22 not output)
• 

CS2

 valid

• Long wait function

Figure 8.7   Memory Map of Area 2

Summary of Contents for HD6417032



















































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HD6417032

Mackie SP260 Installation Instructions preview
SP260
Brand: Mackie Pages: 2
Mackie SP260 Product Overview preview
SP260
Brand: Mackie Pages: 5
dbx Zone Pro 640 Manual preview
Zone Pro 640
Brand: dbx Pages: 2
dbx 166 Quick Start Manual preview
166
Brand: dbx Pages: 17
Hama 39707 Operating Instruction preview
39707
Brand: Hama Pages: 4
ICP DAS USA I-7532M-FD User Manual preview
I-7532M-FD
Brand: ICP DAS USA Pages: 48
ICP DAS USA WF-2572 User Manual preview
WF-2572
Brand: ICP DAS USA Pages: 24
Opengear IMG4216-25 Quick Start Manual preview
IMG4216-25
Brand: Opengear Pages: 2
National Instruments FieldPoint cFP-RTD-122 Operating Instructions Manual preview
FieldPoint cFP-RTD-122
Brand: National Instruments Pages: 15
janitza Procont LMC-008-IO User Manual And Technical Data preview
Procont LMC-008-IO
Brand: janitza Pages: 28
MFJ MFJ-492 Manual preview
MFJ-492
Brand: MFJ Pages: 11
PaloAlto Networks ION 1000 Hardware Reference Manual preview
ION 1000
Brand: PaloAlto Networks Pages: 28
Compal KALA0 Schematics Document preview
KALA0
Brand: Compal Pages: 47
Sony Ericsson GC79 User Manual preview
GC79
Brand: Sony Ericsson Pages: 93
RR-Concepts StationMaster Manual preview
StationMaster
Brand: RR-Concepts Pages: 12
Omron G3RV-SL500-A Manual preview
G3RV-SL500-A
Brand: Omron Pages: 14
LST ZEB2-1 Specifications preview
ZEB2-1
Brand: LST Pages: 1
CSI 7798 I/SITE LAN Installation Manual preview
7798 I/SITE LAN
Brand: CSI Pages: 56

Brands by name

Popular brands

Load more brands