Hitachi HD6417032 Hardware Manual Download Page 144 | Manualshive

Page: 144 / 690

background image

109

8.2.2

Wait State Control Register 1 (WCR1)

Wait state control register 1 is a 16-bit read/write register that controls the number of states for
accessing each area and whether wait states are used. WCR1 is initialized to H'FFFF by a power-
on reset. It is not initialized by a manual reset or in standby mode.

Bit:

15

14

13

12

11

10

9

8

Bit name:

RW7

RW6

RW5

RW4

RW3

RW2

RW1

RW0

Initial value:

1

1

1

1

1

1

1

1

R/W:

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

Bit:

7

6

5

4

3

2

1

0

Bit name:

—

—

—

—

—

—

WW1

—

Initial value:

1

1

1

1

1

1

1

1

R/W:

—

—

—

—

—

—

R/W

—

•

Bits 15–8 (Wait State Control During Read (RW7–RW0)): RW7–RW0 determine the number
of states in read cycles for each area and whether or not to sample the signal input from the

WAIT

pin. Bits RW7–RW0 correspond to areas 7–0, respectively. If a bit is cleared to 0, the

WAIT

signal is not sampled during the read cycle for the corresponding area. If it is set to 1,

sampling takes place.

For the external memory spaces of areas 1, 3–5, and 7, read cycles are completed in one state
when the corresponding bits are cleared to 0. When they are set to 1, the number of wait states
is 2 plus the

WAIT

signal value. For the external memory space of areas 0, 2, and 6, read

cycles are completed in one state plus the number of long wait states (set in wait state
controller 3 (WCR3)) when the corresponding bits are cleared to 0. When they are set to 1, the
number of wait states is 1 plus the long wait state; when the

WAIT

signal is low as well, a wait

state is inserted.

The DRAM space (area 1) finishes the column address output cycle in one state (short pitch)
when the RW1 bit is 0, and in 2 states plus the

WAIT

signal value (long pitch) when RW1 is 1.

When RW1 is set to 1, the number of wait states selected in wait state insertion bits 1 and 0
(RLW0 and RLW1) for CAS-before-RAS (CBR) refresh in the refresh control register (RCR)
are inserted during the CBR refresh cycle, regardless of the status of the

WAIT

signal.

The read cycle of the address/data multiplexed I/O space (area 6) is 4 states plus the wait states
from the

WAIT

signal, regardless of the setting of the RW6 bit. The read cycle of the on-chip

supporting module space (area 5) finishes in 3 states, regardless of the setting of the RW5 bit,
and the

WAIT

signal is not sampled. The read cycles of on-chip ROM (area 0) and on-chip

RAM (area 7) finish in 1 state, regardless of the settings of bits RW0 and RW7. The

WAIT

signal is not sampled for either.

«
...
142
143
144
145
146
...
»

Summary of Contents for HD6417032



















































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HD6417032

Brand: NAIM Pages: 2

Brand: LORD Pages: 9

Brand: Klark Teknik Pages: 50

Brand: Commell Pages: 9

8677 - BladeCenter Rack-mountable - Power Supply

Brand: IBM Pages: 126

NIC-FC730i-Mb-2-32G

Brand: H3C Pages: 37

Vortex86SX VSX-6100

Brand: ICOP Technology Pages: 50

Brand: Baikal Miner Pages: 14

Brand: Xinje Pages: 76

Brand: Juniper Pages: 6

Brand: ekwb Pages: 10

Brand: Thecus Pages: 148

Brand: ZALMAN Pages: 6

32R1860 - Nortel Layer 2/3 Copper GbE Switch...

Brand: IBM Pages: 14

Brand: Accusys Pages: 12

Brand: Cambium Networks Pages: 7

C32C824151 - UB E02 Print Server

Brand: Epson Pages: 84

Brand: Epson Pages: 168

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands