manualshive.com logo in svg

Hitachi HD6417032, Hardware Manual

The "Hitachi HD6417032" Hardware Manual is available for free download on our website. This comprehensive manual provides detailed instructions on operating, maintaining, and troubleshooting the HD6417032, ensuring that users have the necessary information to fully utilize this product. Download your manual now from manualshive.com!

Share
Download
background image

190

9.3.2

DMA Transfer Requests

DMA transfer requests are basically generated in either the data transfer source or destination, but
they can also be generated by devices and on-chip supporting modules that are neither the source
nor the destination. Transfers can be requested in three modes: auto-request, external request, and
on-chip module request. The request mode is selected with the RS3–RS0 bits in the DMA channel
control registers 0–3 (CHCR0–CHCR3).

Auto-Request Mode: When there is no transfer request signal from an external source, as in a
memory-to-memory transfer or a transfer between memory and an on-chip supporting module
unable to request a transfer, the auto-request mode allows the DMAC to automatically generate a
transfer request signal internally. When the DE bits in CHCR0–CHCR3 and the DME bit in
DMAOR are set to 1, the transfer begins (so long as the TE bits in CHCR0–CHCR3 and the NMIF
and AE bits in DMAOR are all 0).

External Request Mode: In this mode a transfer is performed in response to a request signal
(

DREQ

) of an external device. Choose one of the modes shown in table 9.3 according to the

application system. When this mode is selected, if DMA transfer is enabled (DE = 1, DME = 1,
TE = 0, NMIF = 0, AE = 0), a transfer is performed upon a request at the 

DREQ

 input. Choose to

detect 

DREQ

 by either the falling edge or low level of the signal input with the DS bit in CHCR0–

CHCR3 (DS = 0 specifies level detection, DS = 1 specifies edge detection). The source of the
transfer request does not have to be the data transfer source or destination.

Table 9.3

Selecting External Request Modes with the RS Bits

RS3

RS2

RS1

RS0

Address Mode

Source

Destination

0

0

0

0

Dual address
mode

Any

*

Any

*

0

0

1

0

Single address
mode

External memory or
memory-mapped
external device

External device with
DACK

0

0

1

1

Single address
mode

External device with
DACK

External memory or
memory-mapped
external device

Note: 

*

External memory, memory-mapped external device, on-chip memory, on-chip supporting
module (excluding DMAC)

On-Chip Module Request: In this mode a transfer is performed in response to a transfer request
signal (interrupt request signal) of an on-chip module. The transfer request signals include the
receive data full interrupt (RXI) of the serial communication interface (SCI), the transmit data
empty interrupt (TXI) of the SCI, the input capture A/compare match A interrupt request (IMIA)
of the 16-bit integrated pulse timer (ITU), and the A/D conversion end interrupt (ADI) of the A/D
converter (table 9.4). When this mode is selected, if DMA transfer is enabled (DE = 1, DME = 1,
TE = 0, NMIF = 0, AE = 0), a transfer is performed upon input of a transfer request signal. The

Summary of Contents for HD6417032



















































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HD6417032

M-Audio Computer Quick Start Manual preview
Computer
Brand: M-Audio Pages: 10
National Instruments NI 9213 Getting Started preview
NI 9213
Brand: National Instruments Pages: 11
Keithley PDISO-8 User Manual preview
PDISO-8
Brand: Keithley Pages: 71
Omron ACCURAX G5 - Quick Start Manual preview
ACCURAX G5 -
Brand: Omron Pages: 13
C&T Solution VCO-6131E-4M2 User Manual preview
VCO-6131E-4M2
Brand: C&T Solution Pages: 129
Radica Games DAVID-II 716 Operating And Maintenance Instruction Manual preview
DAVID-II 716
Brand: Radica Games Pages: 40
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Brand: Airvana Pages: 90
Renesas HD74HCT1G04 Datasheet preview
HD74HCT1G04
Brand: Renesas Pages: 8
Gigamon GigaVUE H TA100-CXP Hardware Installation Manual preview
GigaVUE H TA100-CXP
Brand: Gigamon Pages: 115
Allen-Bradley SLC 5/03 Installation Instructions Manual preview
SLC 5/03
Brand: Allen-Bradley Pages: 76
Harman Lexicon MPX 200 User Manual preview
Lexicon MPX 200
Brand: Harman Pages: 77
Nexus OSL101 Instructions Manual preview
OSL101
Brand: Nexus Pages: 9
ZALMAN ZM-RWB1 User Manual preview
ZM-RWB1
Brand: ZALMAN Pages: 6
QNAP QSW-3216R-8S8T Quick Installation Manual preview
QSW-3216R-8S8T
Brand: QNAP Pages: 11
Qorvo QPE6105A Manual preview
QPE6105A
Brand: Qorvo Pages: 15
Advantage Boost Box Setup Manual preview
Boost Box
Brand: Advantage Pages: 4
Advantech AIMB-788 User Manual preview
AIMB-788
Brand: Advantech Pages: 114
Crestron RACK2 Operation Manual preview
RACK2
Brand: Crestron Pages: 52

Brands by name

Popular brands

Load more brands