Miscellaneous
183
4812313240.pdf
2017-12-1
1-14 = single lashings, i.e. one lashing with two parts, one head on the machine,
another head on the platform.
The lashings' permitted distance interval in meters
1, 6,7,12: Single lashings, LC at least 6 tonnes (60 KN)
2-5, 8-11: Single lashings, LC at least 8 tonnes (80 KN)
13, 14: Single lashings, LC at least 1 tonnes (10 KN)
L1/L6 L2 L3 L4 L14
1.0-1.5 1.0-1.5 1.0-1.5
1.0-1.5 0.5-1.5
Load carrier-
The machine must always be reversed up the ramp with the rear end
pointing in the direction of travel of the transport vehicle.
- When loaded, the planer is not centered laterally on the platform, refer fig 1
dimension, d1=d2=145mm+50mm
-The steering angle of the front wheels must be zero.
-The drive motor of wheel/track should be locked.
- Lower the machine until the milling drum is just above the ground (approx. 5 cm), or
if wooden supports are used the drum should rest lightly against them.
- Lower the rear scraper, front guard and left/right shields to the lowest position.
- Lower the roof to its lowest position. Extruding control equipment must be retracted,
or removed.
- The parking brake is applied and in good working condition and stop the engine.
- If the conveyor belt is mounted, place it on its support and lash it as per fig. 1
-Chock all machine wheels/tracks, strongly recommend non-slip mat under
wheel/track to increase the friction factor.
- The contact surfaces must be clean, wet or dry, and free from frost, ice and snow.
- The lashing mounts on the load carrier have LC/MSL at least 10 tonnes.
Secure PL2000F for transporting.
(The instructions also apply to machine without
conveyor.)
Direct of trave
l
Fig.1
Table.1
Summary of Contents for PL2000F
