manualshive.com logo in svg

Dräger Infinity Acute Care System M540, Instructions For Use Manual

Share
Download
Dräger Infinity Acute Care System M540 Instructions For Use Manual Download Page 273

Instructions for use – Infinity Acute Care System – Monitoring Applications VG6.n

273

SpO2 and pulse rate with Nellcor OxiMax MCable

SpO2 precautions

Interfering substances: Carboxyhemoglobin may 
erroneously increase measurement values. The 
level of increase is approximately equal to the 
amount of carboxyhemoglobin present. Dyes, or 
any substance containing dyes that change arterial 
pigmentation may cause erroneous measurement 
values.

-------------------------------------------------------------------

WARNING
High oxygen levels may predispose a 
premature baby to retinopathy of prematurity. 
If this is a consideration do NOT set the high 
alarm limit to 100%, which is equivalent to 
switching the alarm off. Transcutaneous SpO2 
monitoring is recommended for premature 
babies receiving supplemental oxygen.

WARNING
An SpO2 sensor should not be used as an 
apnea monitor.

WARNING
Use only 

Nellcor- 

and Dräger-specified 

sensors. Other sensors may not provide 
adequate protection against defibrillation and 
may put the patient at risk. 

WARNING
An SpO2 sensor should be considered an 
early warning device. If a trend towards 
patient hypoxemia is observed, blood 
samples should be analyzed by laboratory 
instruments to completely understand the 
condition of the patient.

WARNING
The pulsations from an intra-aortic balloon 
support can elevate the pulse rate. Verify the 
pulse rate of the patient against the heart rate.

WARNING
To reduce the hazard of burns during surgery, 
keep the sensor or transducer and their 
associated cables away from the surgical site, 
the electro-surgical unit return electrode, and 
earth ground.

WARNING
Inspect the application site every two to three 
hours to ensure skin quality and correct 
optical alignment. If the skin quality changes, 
move the sensor to another site. Change the 
application site at least every four hours.

WARNING
Patient injury can occur if the oximeter is 
applied wrong or if it is subject to excessive 
pressure over a prolonged interval. 

CAUTION

Do not immerse the sensor or patient cable in any 
liquid. Moisture may present a safety risk.

NOTE

An SpO2 sensor can be used during defibrillation, 
but the readings may be inaccurate for up to 
20 seconds.

NOTE

Possession or purchase of this device does not 
convey any express or implied license to use the 
device with unauthorized consumable products 
which would, alone, or in combination with this 
device, fall within the scope of one or more of the 
patents relating to this device and/or consumable 
products. For a list of approved sensors, see the 
Instructions for use 

Infinity Acute Care System

 – 

Accessories

.

Summary of Contents for Infinity Acute Care System M540



































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands