manualshive.com logo in svg

Dräger Infinity Acute Care System M540, Instructions For Use Manual

Share
Download
Dräger Infinity Acute Care System M540 Instructions For Use Manual Download Page 254

SpO2 and Pulse CO-Ox monitoring with Masimo SET MCable

254

Instructions for use – Infinity Acute Care System – Monitoring Applications VG6.n

SpO2

 and 

Pulse CO-Ox precautions

SpO2

 monitoring is only possible with an 

SpO2

 

MCable. 

Interfering substances: Carboxyhemoglobin may 
erroneously increase measurement values. The 
level of increase is approximately equal to the 
amount of carboxyhemoglobin present. Dyes, or 
any substance containing dyes that change arterial 
pigmentation, may cause erroneous measurement 
values.

-------------------------------------------------------------------

WARNING
High oxygen levels may predispose a 
premature baby to retinopathy of prematurity. 
If this is a consideration do NOT set the high 
alarm limit to 100%, which is equivalent to 
switching the alarm off. Transcutaneous SpO

2

 

monitoring is recommended for premature 
babies receiving supplemental oxygen.

WARNING
An SpO

2

 sensor should not be used as an 

apnea monitor.

WARNING
Use only Masimo-specified sensors. Other 
sensors may not provide adequate protection 
against defibrillation and may put the patient 
at risk.

WARNING
A Pulse CO-Oximeter should be considered 
an early warning device. If a trend towards 
patient hypoxemia is observed, blood 
samples should be analyzed by laboratory 
instruments to completely understand the 
condition of the patient.

WARNING
The pulsations from an intra-aortic balloon 
support can elevate the pulse rate. Verify the 
pulse rate of the patient against the heart rate.

WARNING
Elevated levels of methemoglobin (MetHb) 
may lead to inaccurate SpO2 and SpCO 
measurements.

Elevated levels of total bilirubin may lead to 
inaccurate SpO2, SpMet, SpCO, SpHb, and 
SpOC measurements.

Motion artifact may lead to inaccurate SpMet, 
SpCO, SpHb, and SpOC measurements.

Very low arterial oxygen saturation (SaO2) 
levels may cause inaccurate SpCO and SpMet 
measurements.

Hemoglobin synthesis disorders may cause 
erroneous SpHb readings.

WARNING
To reduce the hazard of burns during surgery, 
keep the sensor or transducer and their 
associated cables away from the surgical site, 
the electro-surgical unit return electrode, and 
earth ground.

WARNING
Inspect the application site every two to three 
hours to ensure skin quality and correct 
optical alignment. If the skin quality changes, 
move the sensor to another site. Change the 
application site at least every four hours. The 
misapplication of an SpO

2

 sensor with 

excessive pressure for prolonged periods can 
induce pressure injury. 

CAUTION

Do not immerse the sensor or patient cable in any 
liquid. Moisture may present a safety risk.

Summary of Contents for Infinity Acute Care System M540



































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands