manualshive.com logo in svg

Digi NS9215, Hardware Reference Manual, Page: 341 / 517

Share
Download
Digi NS9215 Hardware Reference Manual Download Page 341

. . . . .

E X T E R N A L   D M A

Descriptor list processing

www.digiembedded.com

341

Note:

Optimal performance is achieved when the destination address is aligned on a 
word boundary.

Status

This field is not used. Read back 0x0000.

Wrap (W) bit

The Wrap (W) bit, when set, tells the DMA controller that this is the last buffer 
descriptor within the continuous list of descriptors. The next buffer descriptor is 
found using the initial DMA channel buffer descriptor pointer. When the W bit is not 
set, the next buffer descriptor is found using an offset of 0x10 from the current 
buffer descriptor.

Interrupt (I) bit

The Interrupt (I) bit, when set, tells the DMA controller to issue an interrupt to the 
CPU when the buffer is closed due to a normal channel completion. The interruption 
occurs regardless of the normal completion interrupt enable configuration for the 
DMA channel.

Last (L) bit

The Last (L) bit, when set, tells the DMA controller that this buffer descriptor is the 
last descriptor that completes an entire message frame. The DMA controller uses this 
bit to assert the normal channel completion status when the byte count reaches zero.

Full (F) bit

The Full (F) bit, when set, indicates that the buffer descriptor is valid and can be 
processed by the DMA channel. The DMA channel clears this bit after completing the 
transfer(s). 

The DMA channel does not try a transfer with the F bit clear. The DMA channel 
enters an idle state upon fetching a buffer descriptor with the F bit cleared. 
Whenever the F bit is modified by the device driver, the device driver must also 
write a 1 to the CE bit in the DMA Control register to activate the idle channel.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

D e s c r i p t o r   l i s t   p r o c e s s i n g

Once a DMA controller has completed the operation specified by the current buffer 
descriptor, it clears the F bit and fetches the next buffer descriptor. A DMA channel 
asserts the NRIP field (buffer not ready interrupt pending) in the DMA Status 
register and returns to the idle state upon fetching a buffer descriptor with the F bit 
in the incorrect state. A DMA channel always closes the current descriptor and 
moves on to the next descriptor when a DMA transfer is terminated by the assertion 
of the DONE signal.

Summary of Contents for NS9215






































































































































































































































































































































































































































































































































Reviews:

No comments