manualshive.com logo in svg

Digi NS9215, Hardware Reference Manual, Page: 148 / 517

Share
Download
Digi NS9215 Hardware Reference Manual Download Page 148

S Y S T E M   C O N T R O L   M O D U L E

Interrupt controller

148

Hardware Reference NS9215

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

I n t e r r u p t   c o n t r o l l e r

The interrupt system is a simple two-tier priority scheme. Two lines access the CPU 
core and can interrupt the processor: IRQ (normal interrupt) and FIQ (fast 
interrupt). FIQ has a higher priority than IRQ.

FIQ interrupts

Most sources of interrupts on the processor are from the IRQ line. There is only one 
FIQ source for timing-critical applications. The FIQ interrupt generally is reserved 
for timing-critical applications for these reasons:

The interrupt service routine is executed directly without determining the 
source of the interrupt.

Interrupt latency is reduced. The banked registers available for FIQ interrupts 
are more efficient because a context save is not required.

Note:

The interrupt source assigned to the FIQ must be assigned to the highest 
priority, which is 0.

IRQ interrupts

IRQ interrupts come from several different sources in the processor and are 
managed using the Interrupt Config registers (see “Int (Interrupt) Config 
(Configuration) 31–0 registers” on page 175). IRQ interrupts can be enabled or 
disabled on a per-level basis using the Interrupt Enable registers. These registers 
serve as masks for the different interrupt levels. Each interrupt level has two 
registers: 

Interrupt Configuration register. Use this register to assign the source for 
each interrupt level, invert the source polarity, select IRQ or FIQ, and enable 
the level. 

Interrupt Vector Address register. Contains the address of the interrupt 
service routine.

32-vector 
interrupt 
controller

The next figure shows a 32-vector interrupt controller:

Summary of Contents for NS9215






































































































































































































































































































































































































































































































































Reviews:

No comments