manualshive.com logo in svg

Digi NS9215, Hardware Reference Manual, Page: 329 / 517

Share
Download
Digi NS9215 Hardware Reference Manual Download Page 329

. . . . .

E T H E R N E T   C O M M U N I C A T I O N   M O D U L E

Multicast Address Mask registers

www.digiembedded.com

329

Multicast High 
Address Filter 
Register #6

Address: A060 0A78 

Multicast High 
Address Filter 
Register #7

Address: A060 0A7C 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

M u l t i c a s t   A d d r e s s   M a s k   r e g i s t e r s

Each of the eight entries in the multicast address filter logic has individual mask 
registers that extend the filtering range of each entry. The multicast address mask 
for each entry is split between two registers. Each entry has a register that contains 
the lower 32 bits of the multicast mask and a separate register that contains the 
upper 16 bits of the mask. 

Bits are set to 1 in the mask to enable or include that bit in the address filter.

Bits are set to 0 in the mask if they are not included or are disabled in the 
address filter. These bits become don’t cares.

For an explanation of the synchronization scheme used for these registers, see 
“Clock synchronization” on page 276.

Multicast Low 
Address Mask 
Register #0

Address: A060 0A80 

Multicast Low 
Address Mask 
Register #1

Address: A060 0A84 

Multicast Low 
Address Mask 
Register #2

Address: A060 0A88 

Multicast Low 
Address Mask 
Register #3

Address: A060 0A8C 

D31:16

R

Default = 0x0000 0000

Reserved (read as 0)

D15:00

R/W

Default = 0x0000 0000

MFILTH6

D31:16

R

Default = 0x0000 0000

Reserved (read as 0)

D15:00

R/W

Default = 0x0000 0000

MFILTH7

D31:00

R/W

Default = 0x0000 0000

MFMSKL0

D31:00

R/W

Default = 0x0000 0000

MFMSKL1

D31:00

R/W

Default = 0x0000 0000

MFMSKL2

D31:00

R/W

Default = 0x0000 0000

MFMSKL3

Summary of Contents for NS9215






































































































































































































































































































































































































































































































































Reviews:

No comments