manualshive.com logo in svg

Digi NS9215, Hardware Reference Manual, Page: 273 / 517

Share
Download
Digi NS9215 Hardware Reference Manual Download Page 273

. . . . .

E T H E R N E T   C O M M U N I C A T I O N   M O D U L E

Ethernet slave interface

www.digiembedded.com

273

–

A packet consisting of multiple, linked buffer descriptors does not have the F 
bit set in any of the non-first buffer descriptors.

When an underrun occurs, it is also possible for the Ethernet transmitter to send out 
a corrupted packet with a good Ethernet CRC if the MAC is configured to add the 
CRC to the frame (that is, CRCEN in MAC Configuration Register #2 is set to 1).

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

E t h e r n e t   s l a v e   i n t e r f a c e

The AHB slave interface supports only single 32-bit transfers. The slave interface 
also supports limiting CSR and RAM accesses to CPU “privileged mode” accesses. 
Use the 

internal register access mode

 bit 0 in the Miscellaneous System Configuration 

register to set access accordingly (see "Miscellaneous System Configuration and 
Status register," beginning on page 184). 

The slave also generates an AHB 

ERROR

 if the address is not aligned on a 32-bit 

boundary, and the misaligned bus address response mode is set in the Miscellaneous 
System Configuration register. In addition, accesses to non-existent addresses result 
in an AHB 

ERROR

 response.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

I n t e r r u p t s

Separate RX and TX interrupts are provided back to the system. 

Interrupt sources

This table shows all interrupt sources and the interrupts to which they are assigned.

Interrupt condition

Description

Interrupt

RX data FIFO overflow

RX data FIFO overflowed.
For proper operation, reset the receive packet processor using the 
ERX bit in the Ethernet General Control Register #1 when this 
condition occurs. 

RX

RX status FIFO overflow RX status overflowed.

RX

Receive buffer closed

I bit set in receive buffer descriptor and buffer closed.

RX

Receive complete (Pool 
A)

Complete receive frame stored in pool A of system memory.

RX

Receive complete (Pool 
B)

Complete receive frame stored in pool B of system memory.

RX

Receive complete (Pool 
C)

Complete receive frame stored in pool C of system memory.

RX

Receive complete (Pool 
D)

Complete receive frame stored in pool D of system memory.

RX

Summary of Contents for NS9215






































































































































































































































































































































































































































































































































Reviews:

No comments