manualshive.com logo in svg

Digi NS9215, Hardware Reference Manual, Page: 280 / 517

Share
Download
Digi NS9215 Hardware Reference Manual Download Page 280

E T H E R N E T   C O M M U N I C A T I O N   M O D U L E

Ethernet General Control Register #1

280

Hardware Reference NS9215

Register bit 
assignment

Bits

Access

Mnemonic

Reset

Description

D31

R/W

ERX

0

Enable RX packet processing 

0

Reset RX

1

Enable  RX

Used as a soft reset for the RX. When cleared, resets all 
logic in the RX and flushes the FIFO.
The ERX bit must be set active high to allow data to be 
received from the MAC receiver. 

D30

R/W

ERXDMA

0

Enable receive DMA

0

Disable receive DMA data request (use to stall 
receiver)

1

Enable receive DMA data request

Must be set active high to allow the 

RX_RD

 logic to request 

the AHB bus to DMA receive frames into system memory. 
Set this bit to zero to temporarily stall the receive side 
Ethernet DMA. The 

RX_RD

 logic stalls on frame 

boundaries.

D29

N/A

Reserved

N/A

N/A

D28

R/W

ERXSHT

0

Accept short (<64) receive frames

0

Do not accept short frames

1

Accept short frames

When set, allows frames that are smaller than 64 bytes to 
be accepted by the 

RX_WR

 logic. 

ERXSHT is typically set for debugging only.

D27:24

R/W

Not used

0

Always write as 0.

D23

R/W

ETX

0

Enable TX packet processing 

0

Reset TX

1

Enable  TX

Used as a soft reset for the TX. When cleared resets all 
logic in the TX and flushes the FIFOs. 
ETX must be set active high to allow data to be sent to the 
MAC and to allow processor access to the TX buffer 
descriptor RAM.

Summary of Contents for NS9215






































































































































































































































































































































































































































































































































Reviews:

No comments