manualshive.com logo in svg

Digi NS9215, Hardware Reference Manual, Page: 217 / 517

Share
Download
Digi NS9215 Hardware Reference Manual Download Page 217

. . . . .

M E M O R Y   C O N T R O L L E R

Static memory Write: Timing and parameters

www.digiembedded.com

217

External memory 
write transfer 
with two wait 
states

This diagram shows a single external memory write transfer with two wait states 
(

WAITWR=2

). One AHB wait state is added. 

External memory 
write transfer 
with two write 
enable delay 
states

This diagram shows a single external memory write transfer with two write enable 
delay states (

WAITWEN=2

). One wait state is added.

Timing parameters

Value

WAITRD

N/A

WAITOEN

N/A

WAITPAGE

N/A

WAITWR

0

WAITWEN

0

WAITTURN

N/A

Timing parameter

Value

WAITRD

N/A

WAITOEN

N/A

WAITPAGE

N/A

WAITWR

2

WAITWEN

0

WAITTURN

N/A

A

D(A)

clk_out

addr

data

cs{n}

st_we_n

A

D(A)

clk_out

addr

data

cs[n]

st_we_n

Summary of Contents for NS9215






































































































































































































































































































































































































































































































































Reviews:

No comments