ABB IRB 1200 Page 740 Product Manual Download

Page: 740 / 906

4.6.6 Replacing the axis-4 timing belt

Location of timing belt

The axis-4 timing belt is located as shown in the figure.

xx1400000036

Required spare parts

Note

The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,

www.abb.com/myABB

Note

Article number

Spare part

3HAC044694-001

Timing belt

Not used with protection class
IP40.
Replace if damaged.

3HAC056724-001 /
3HAC080702-001

Gasket on cable housing cover

Not used with protection class
IP40.
Replace if damaged.

3HAC056698-001 /
3HAC080700-001

Housing cover gasket (IRB
1200-7/0.7 )

Not used with protection class
IP40.
Replace if damaged.

3HAC056697-001 /
3HAC080699-001

Housing cover gasket (IRB
1200-5/0.9 )

Continues on next page

740

Product manual - IRB 1200

3HAC046983-001 Revision: S

4 Repair

4.6.6 Replacing the axis-4 timing belt

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

Related manuals for IRB 1200

Brands by name

Popular brands

ABB IRB 1200, Product Manual

Search results

Summary of Contents for IRB 1200

Reviews:

Related manuals for IRB 1200

Brands by name

Popular brands