ABB IRB 1200 Page 412 Product Manual Download

Page: 412 / 906

Note

Action

Screws: 3HAB3409-212 (M4x16).

xx1300002463

Place the motor at its mounting position and
fasten the attachment screws and washers just
enough to still be able to move the motor.

Note

Only use specified screws, never
replace them with other screws.

Securing the axis-5 motor and timing belt

Note

Action

For robots with protection type Clean
Room

For robots with food grade lubrication
For robots with protection type Hygienic

Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.

xx1300002351

Refit the timing belt on the pulley.

Note

Do not strech the timing belt too much!

Move the motor to a position where a good
timing belt tension is reached (F = 26 N).

Continues on next page

412

Product manual - IRB 1200

3HAC046983-001 Revision: S

4 Repair

4.4.3 Replacing the tubular spare parts

Continued

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

Related manuals for IRB 1200

Brands by name

Popular brands

ABB IRB 1200, Product Manual

Search results

Summary of Contents for IRB 1200

Reviews:

Related manuals for IRB 1200

Brands by name

Popular brands