ABB IRB 1200 Product Manual Download Page 825

Page: 825 / 906

xx1600001036

Spare parts

When calibration is not being performed, a protective plug should always be
installed in the bushing. Replace damaged parts with new, if needed.

Note

Article number

Spare part

Replace if damaged or missing.

3HAC059556-001

Protective plug for bushing

Used with protection type Clean
Room

3HAC059557-001

Protective plug for bushing, Clean
Room

Used for robots with food grade
lubrication

Protective plug for bushing, food
grade lubrication

Used with protection type Hygien-
ic

Protective plug for bushing, Hygien-
ic

Replace if damaged or missing.

Product manual - IRB 1200

825

3HAC046983-001 Revision: S

5 Calibration

5.4.3 Installation locations for the calibration tools

Continued

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

ABB IRB 1200, Product Manual, Page: 825 / 906

Search results

Summary of Contents for IRB 1200

Reviews: