ABB IRB 1200 Product Manual Download Page 343

Page: 343 / 906

Refitting the upper arm

Note

Action

For robots with protection type Clean
Room

For robots with food grade lubrication
For robots with protection type Hygienic

Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.

Guide pin for upper arm: 3HAC049705-001

Fit guide pins to the axis-3 gear unit.

Always use three guide pins together!

xx1400000027

M2 variseal sealing: 3HAC044641-005

xx1400000474

For robots with protection class IP67
For robots with protection type Foundry
Plus

Check the sealing.
Replace if damaged.

CAUTION

Do not fit M2 variseal sealing on robots in
other protection class or protection types.

Continues on next page

Product manual - IRB 1200

343

3HAC046983-001 Revision: S

4 Repair

4.4.1 Replacing the lower arm

Continued

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

ABB IRB 1200, Product Manual, Page: 343 / 906

Search results

Summary of Contents for IRB 1200

Reviews: