ABB IRB 1200 Page 418 Product Manual Download

Page: 418 / 906

4.4.4 Replacing the axis-3 radial sealing and sealing ring

Location of the sealings

The axis-3 radial sealing and sealing ring are located as shown in the figure.

xx1400000336

Required spare parts

Note

The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,

www.abb.com/myABB

Note

Article number

Spare part

Not used with protection class
IP40.
Replace if damaged.

3HAC024865-001

Radial sealing

Used with protection class IP67.
Used with protection type
Foundry Plus.
Replace if damaged.

3HAC044641-006

M2 variseal sealing

Continues on next page

418

Product manual - IRB 1200

3HAC046983-001 Revision: S

4 Repair

4.4.4 Replacing the axis-3 radial sealing and sealing ring

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

Related manuals for IRB 1200

Brands by name

Popular brands

ABB IRB 1200, Product Manual

Search results

Summary of Contents for IRB 1200

Reviews:

Related manuals for IRB 1200

Brands by name

Popular brands