ABB IRB 1200 Page 198 Product Manual Download

Page: 198 / 906

Note

Action

xx1300000472

Pull out the base slightly and turn it aside.

Tip

Remember the cable layout in the base. The
cabling must be positioned and angled in the
same way during refitting.

Removing the cable package from the axis-1 sealing ring

Note

Action

DANGER

Make sure that all supplies for electrical power,
hydraulic pressure, and air pressure are turned
off.

CAUTION

For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic

Always cut the paint with a knife and grind the
paint edge when disassembling parts of the robot!
See

Cut the paint or surface on the robot before

replacing parts on page 158

xx1300002438

Remove the axis-1 sealing ring from the swing
and carefully run the cable package out from the
swing.

Remove the swing (including arm system) com-
pletely from the base and lay it aside on a safe
location.

Continues on next page

198

Product manual - IRB 1200

3HAC046983-001 Revision: S

4 Repair

4.3.1 Replacing the main cable package

Continued

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

Related manuals for IRB 1200

Brands by name

Popular brands

ABB IRB 1200, Product Manual

Search results

Summary of Contents for IRB 1200

Reviews:

Related manuals for IRB 1200

Brands by name

Popular brands