ABB IRB 1200 Product Manual Download Page 330

Page: 330 / 906

Note

Action

xx1300002529

Remove the cable housing of the lower arm
by removing the screws.

Removing the upper arm

Note

Action

DANGER

Make sure that all supplies for electrical
power, hydraulic pressure, and air pressure
are turned off.

CAUTION

For robots with protection type Clean
Room
For robots with food grade lubrication
For robots with protection type Hygienic

Always cut the paint with a knife and grind
the paint edge when disassembling parts
of the robot! See

Cut the paint or surface

on the robot before replacing parts on
page 158

Continues on next page

330

Product manual - IRB 1200

3HAC046983-001 Revision: S

4 Repair

4.4.1 Replacing the lower arm

Continued

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

ABB IRB 1200, Product Manual, Page: 330 / 906

Search results

Summary of Contents for IRB 1200

Reviews: