ABB IRB 1200 Product Manual Download Page 201

Page: 201 / 906

Note

Action

xx1400000406

Remove the cable bracket by removing the
screws.

xx1400000407

Remove the bracket inside the base by removing
the screws.

xx1400000411

Pull the cable package out from the base, through
the bottom.

Refitting the main cable package

Use these procedures to refit the cable package.

Adjusting the air hose length for IRB 1200-7/0.7

Note

Action

For robots with protection type Clean Room

For robots with food grade lubrication
For robots with protection type Hygienic

Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.

Continues on next page

Product manual - IRB 1200

201

3HAC046983-001 Revision: S

4 Repair

4.3.1 Replacing the main cable package

Continued

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

ABB IRB 1200, Product Manual, Page: 201 / 906

Search results

Summary of Contents for IRB 1200

Reviews: