ABB IRB 1200 Product Manual Download Page 288

Page: 288 / 906

Note

Action

Tightening torque: 0.3 Nm.

xx1400001402

Secure the three M2.5 screws.

Connecting the axis-5 motor FPC connectors

Note

Action

For robots with protection type Clean
Room

For robots with food grade lubrication
For robots with protection type Hygienic

Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.

xx1300002390

Connect the axis-5 FPC connectors and
snap them to their holders.

Refitting the tubular cable housing cover

Note

Action

For robots with protection type Clean
Room

For robots with food grade lubrication
For robots with protection type Hygienic

Clean the joints that have been opened and
wipe the parts free from particles with
spirit on a lint free.

Continues on next page

288

Product manual - IRB 1200

3HAC046983-001 Revision: S

4 Repair

4.3.3 Replacing the axis-5 FPC unit

Continued

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

ABB IRB 1200, Product Manual, Page: 288 / 906

Search results

Summary of Contents for IRB 1200

Reviews: