ABB IRB 1200 Page 448 Product Manual Download

Page: 448 / 906

Note

Action

xx1500000252

If equipped, reconnect the CP/CS connector.

For robots with protection class IP67
For robots with protection type Foundry Plus

Check the gasket.

Replace if damaged.

For robots with protection type Clean Room
For robots with food grade lubrication

Remove residual locking liquid and other
pollutants with cleaning agent Loctite 7063.

Apply flange sealing Loctite 574 on the
mounting surfaces of the CP/CS connector
and wipe clean if there is any overflowing
Loctite 574.

On robots with protection class
IP67
On robots with protection type
Foundry Plus
Gasket: 3HAC058567-001

xx1500000251

Protection bracket for CP/CS con-
nectors: 3HAC058350-001

xx1600001152

For robots with protection type Foundry Plus

If required, fit the protection bracket for CP/CS
connectors.

Connecting the air hoses and CP/CS cabling on robots in protection type Hygienic

Use this procedure if the robot is with protection type Hygienic.

Note

Action

Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.

Continues on next page

448

Product manual - IRB 1200

3HAC046983-001 Revision: S

4 Repair

4.4.4 Replacing the axis-3 radial sealing and sealing ring

Continued

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

Related manuals for IRB 1200

Brands by name

Popular brands

ABB IRB 1200, Product Manual

Search results

Summary of Contents for IRB 1200

Reviews:

Related manuals for IRB 1200

Brands by name

Popular brands