ABB IRB 1200 Product Manual Download Page 523

Page: 523 / 906

Note

Action

Rear connector interface:

xx1300000470

Remove the axis-1 motor bracket.

Bottom connector interface:

xx1400000404

xx1300002496

Loosen the connectors from the bracket by
cutting the cable straps, and disconnect
the connectors.

Continues on next page

Product manual - IRB 1200

523

3HAC046983-001 Revision: S

4 Repair

4.5.1 Replacing the base spare parts (base, axis-1 radial sealing, protection sleeve)

Continued

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

ABB IRB 1200, Product Manual, Page: 523 / 906

Search results

Summary of Contents for IRB 1200

Reviews: