ABB IRB 1200 Page 534 Product Manual Download

Page: 534 / 906

Note

Action

Sealant: Sikaflex 521FC.

xx1600001125

For robots with protection class IP67

On axis-1 sealing ring version 3HAC056658-001:
Add sealant to the axis-1 sealing ring.
(See

Spare part versions for the axis-1 sealing

ring on IP40/IP67 robots on page 878

On axis-1 sealing ring version
3HAC044676-001:

For robots with protection class IP67

On axis-1 sealing ring version 3HAC044676-001,
3HAC058568-001 or 3HAC068107-001:

Axis-1 sealing ring gasket:
3HAC045685-001

xx1400000458

For robots with protection type Foundry Plus

On axis-1 sealing ring version 3HAC058568-001
or 3HAC068107-001:
Check the gasket on the axis-1 sealing ring.
(See

Spare part versions for the axis-1 sealing

ring on IP40/IP67 robots on page 878

Replace if damaged.

On axis-1 sealing ring version
3HAC058568-001:
Axis-1 sealing ring gasket:
3HAC058349-001 (not Hygienic
robots) / 3HAC080707-001 (Hygien-
ic robots)

xx1600001149

On axis-1 sealing ring version
3HAC068107-001:
Axis-1 sealing ring gasket:
3HAC058349-001 (not Hygienic
robots) / 3HAC080707-001 (Hygien-
ic robots)

xx1900001735

Continues on next page

534

Product manual - IRB 1200

3HAC046983-001 Revision: S

4 Repair

4.5.1 Replacing the base spare parts (base, axis-1 radial sealing, protection sleeve)

Continued

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

Related manuals for IRB 1200

Brands by name

Popular brands

ABB IRB 1200, Product Manual

Search results

Summary of Contents for IRB 1200

Reviews:

Related manuals for IRB 1200

Brands by name

Popular brands