ABB IRB 1200 Product Manual Download Page 758

Page: 758 / 906

4.6.7 Replacing the axis-5 motor with pulley

Location of motor

The axis-5 motor is located as shown in the figure.

xx1300002473

Required spare parts

Note

The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 1200 via myABB Business Portal,

www.abb.com/myABB

Note

Article number

Equipment, etc.

3HAC045978-001

Motor with pulley

Used for IRB 1200 Type B. See

Type

B of IRB 1200 on page 873

3HAC061278-001

Motor with pulley, SafeMove
2-supported.
Motor with pulley, Hygienic

Not used with protection class IP40.

3HAC058822-001 /
3HAC080709-001

Gasket for tubular cover

Replace if damaged.

Not used with protection class IP40.

3HAC056707-001 /
3HAC080701-001

Gasket for tubular cable
housing cover

Replace if damaged.

Continues on next page

758

Product manual - IRB 1200

3HAC046983-001 Revision: S

4 Repair

4.6.7 Replacing the axis-5 motor with pulley

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

ABB IRB 1200, Product Manual, Page: 758 / 906

Search results

Summary of Contents for IRB 1200

Reviews: